The clockrate was the only really needed field from platform data.
Add clk support to retrieve the clockrate and make platform data
optional.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This introduces the ecc stength fields in the structures and fills
them in, but leaves them unused right now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There is the same function name in the Kernel but with different
semantics. Rename to avoid naming conflicts when we update the
mtd support from the kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is based on Linux:
commit e2414f4c20bd4dc62186fbfd7bdec50bce6d2ead
Author: Brian Norris <computersforpeace@gmail.com>
Date: Mon Feb 6 13:44:00 2012 -0800
Currently, the flash-based BBT implementation writes bad block data only
to its flash-based table and not to the OOB marker area. Then, as new bad
blocks are marked over time, the OOB markers become incomplete and the
flash-based table becomes the only source of current bad block
information. This becomes an obvious problem when, for example:
* code accessing the flash cannot read the flash-based BBT format
* BBT is corrupted and the flash must be rescanned for bad
blocks; we want to remember bad blocks that were marked from Linux
So to keep the bad block markers in sync with the flash-based BBT, this
patch changes the default so that we write bad block markers to the proper
OOB area on each block in addition to flash-based BBT. Comments are
updated, expanded, and/or relocated as necessary.
The new flash-based BBT procedure for marking bad blocks:
(1) erase the affected block, to allow OOB marker to be written cleanly
(2) update in-memory BBT
(3) write bad block marker to OOB area of affected block
(4) update flash-based BBT
Note that we retain the first error encountered in (3) or (4), finish the
procedures, and dump the error in the end.
This should handle power cuts gracefully enough. (1) and (2) are mostly
harmless (note that (1) will not erase an already-recognized bad block).
The OOB and BBT may be "out of sync" if we experience power loss bewteen
(3) and (4), but we can reasonably expect that on next boot, subsequent
I/O operations will discover that the block should be marked bad again,
thus re-syncing the OOB and BBT.
Note that this is a change from the previous default flash-based BBT
behavior.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds the possibility to configure the place for the environment
from the devicetree and to partition devices from the devicetree.
Configuration has the general form of devices with a regular compatible
property. This allows to later add additional drivers or drivers with
different behaviour (for example to add support for redundant environment).
The configuration is all in the /chosen/barebox/ hierarchy of the
devicetree. This separates the configuration from the hardware
description. Also it makes it possible to store the configuration
in a completely separate devicetree (or devicetree overlay). For
the same reason all configuration is done using nodepathes rather
than phandles.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MMC/SD cards normally have a DOS/GPT partition table, but sometimes
barebox uses the unpartitioned area to store its environment. Add
devicetree partition parsing also for SD/MMC cards so that we have
a way to describe the partition in the devicetree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
These functions allow to manipulate the "status" property of
devicenodes effectively enabling/disabling devices.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So that users can call the of partition parsers without checking
if they are probed from the devicetree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Mostly taken from the kernel with support for other SoCs from
Alexander Shiyan.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alexander Shiyan <shc_work@mail.ru>
This patch moves support for MC34708 PMIC into mc13xxx driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When changing the rates of the ssp clocks we have to poll the
busy bit, but only when they are enabled. The current code can
not check this properly since the gates are registered as children
of the dividers. This has the effect that when the gate is disabled
the busy bit will be set forever resulting in a freezed system.
Fix this by making the gates parents of the dividers which allows
clk_is_enabled to return the correct result.
The Kernel has the same problem, but here the busy polling is
limited to 10ms, so probably noone noticed this.
The datasheet mentions that the ssp dividers shall only be changed
when the clocks are enabled. The kernel and barebox currently ignore
this. I don't know what effect violating this rule has.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to use device_ids and make code a bit smaller.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to use device_ids and make code a bit smaller.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This change will allow reuse this function for other buses.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a driver option to probe GPIO LEDs from device tree compatible
with "gpio-leds" device tree nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds initialization of from device node with root_node if NULL
is passed. This corresponds to the behavior of all other node iterators.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for the SPI controller found on Marvell MVEBU SoCs
(Dove, Kirkwood, Discovery Innovation, and Armada 370/XP). Current driver
is DT only. Compatible strings are provided for Orion (common denominator),
Armada 370/XP and Dove SoCs.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
of_get_next_available_child does not iterate but always tries the
same node over and over again. This first prepares the entry and
then uses list_for_each_entry_continue, instead of for_each_child_of_node
before.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
of_find_node_by_name suffers from infinite looping, because it
does not check for root node of the tree iterated over. This
fixes this by checking for node->parent to determine whether
the last node has been reached.
Since of_tree_for_each_node does not iterate over the whole tree,
but only over the remaining nodes, rename it to
of_tree_for_each_node_from.
Reported-by: NISHIMOTO Hiroki <hiroki.nishimoto.if@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a DT only driver for the GPIO controller found on Marvell
Orion/MVEBU SoCs (Armada 370/XP, Dove, Kirkwood, MV78x00, Orion5x).
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds device tree support to mvebu timer and also converts clk_get
to clk_lookup to find TCLK without device name reference.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This converts Armada 370/XP SoC init to register tclk alias
for timer by physbase instead of name.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds device tree support to orion timer and also converts clk_get
to clk_lookup to find TCLK without device name reference.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This converts Kirkwood and Dove SoC init to register tclk alias
for timer by physbase instead of name.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
of_free is misleading about the actual purpose of the function. There is
already a of_create_node counterpart, so rename of_free to of_create_node
and update all users accordingly.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Convert of_add_memory parsing to make use of of_address_to_resource
instead of parsing memory ranges itself. This makes some functions
dead code which are also removed.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
struct device_node has its own resources and a pointer to associated
device_d. With recent platform related OF code, we can convert the
only user of it and remove those pointers from struct device_node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With recent conversion to of_platfrom_populate_some functions are now
dead code and can be removed.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With recent bus/device related functions in OF API, we can now
convert to use of_platform_populate.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This creates a Linux OF API compatible counterpart of of_get_named_gpio_flags.
Existing of_get_named_gpio is converted to a static inline function, which is
in the corresponding of_gpio.h include. While at it, drivers/of/gpio.c is
also renamed to drivers/of/of_gpio.c to follow the of_ prefix naming scheme.
The new include is also added to existing users of of_get_named_gpio.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This imports some bus and device related functions from Linux OF API
with some modifcations for Barebox.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
OF_ROOT_NODE_* defines should not be used outside of base.c. Move them
to drivers/of/base.c to ensure they will not be used elsewhere.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This converts existing of_translate_address to recently added API. In
contrast to existing behavior, the new function honors ranges properties
properly. It now allows reg properties to be set as offset with respect
to the correspoding parent node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This imports drivers/of/address.c from Linux with some minor modifications.
of_translate_address is not yet enabled and PCI and ISA related bus translations
have not been imported. Also, a corresponding include header is created with
prototypes and non-OF function stubs.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Only UART clocks are included for now, but the code should cover
other peripherals needs, too.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This removes the existing Tegra CAR driver and replaces it with code
ported from the Linux clock framework.
In the current state only the relevant PLLs are supported, but this is
no functional regression from the existing code.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Allows to reuse the clk gate code within other clocks.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Taken from the Linuxkernel with some small adjustments for barebox.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Clocksource read callback expects incrementing timer values, while
internal timer on Marvell SoCs counts backwards. Fix value returned
by Marvell MVEBU and Orion clocksource drivers.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The upcoming multi image support will need devicetree binary
blobs even when there is no builtin dtb. Instead of depending
on CONFIG_BUILTIN_DTB depend on CONFIG_OFTREE and let this option
select DTC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It becomes a common pattern for boards to find a device and
call device_detect on it. Add a convenience wrapper for it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This commit creates MDIO bus devices to separate the MDIO bus
abstraction from the Ethernet device initialisation.
It also updates the configuration of the P2020RDB ports.
Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The fsl gadget driver wants to configure the portsc register
with information from platform_data. When registered from the
chipidea driver there is no platform_data. Fix the resulting
crash by not derefencing platform_data when NULL. In this
case the PORTSC register is not touched, it will have been
configured by the chipidea driver in this case.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Probe ULPI phys during USB initialization and not during driver
probe. This lowers the pressure to have the necessary board specific
setup in place early.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We used to distinguish which USB port to fixup by pdev->id. This
is < 0 for devicetree probed devices all the time, so this won't
work anymore once we switch to devicetree. Do the fixup on every
port instead, it doesn't hurt.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds omap display controller support. Currently only
OMAP4 DSS is supported.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Chipsize didn't take number of LUNs into account. Sync chipsize calculation
to kernel commit 63795755
Tested with MT29F8G16ADBDAH4 on OMAP4
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch makes OF API use of_delete_property where applicable instead
of freeing allocated data in different places.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds some sanity checks to of_new_property and of_delete_property.
Also, value pointer is always allocated even with zero length to allow
empty properties to be distinguished from non-existing properties.
Finally, data passed to of_new_property is only copied if non-NULL.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
ENABLE_DEVICE_NOISE is used only in two network drivers and is
otherwise unused. ENABLE_FLASH_NOISE is completely unused.
ENABLE_PARTITION_NOISE enables DEBUG in the partition command,
but this code has no debug messages at all.
Remove all this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch removes the call of the cpu_is_* functions completely
and uses id_tables instead.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added device register functions and cpu_is_am33xx()
function.
Adapted the i2c-omap driver. AM335x has a lower
clock rate and the timeout of polling the isr function
had to be increased.
Based on a patch from Shravan Kumar <shravan.k@phytec.in>.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
cpu_is_omap2430() is set when CONFIG_ARCH_OMAP is enabled.
This fits for all OMAP/AM33xx boards supported in barebox.
Cleaned up all conditions that use the cpu_is_omap2430().
Also removed some unused defines.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Board file or DT has to take care that the correct
chip select and bus values are used.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently we can only (re)scan all USB hosts. Add a function to
scan individual hosts. This is useful for implementing the detect
callback in the next patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A command should not be interested in the internal USB core state, so
move the state handling into the core.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This renames the USB devices to reflect the bus structure.
The base name for a USB device is usb<devno>. For each child
device we add a -<parent-port-no>. This makes it more easy
to identify devices.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Embedding struct ata_ioports into struct ide_port saves us an allocation.
Making it available to client drivers is necessary to give them access
to struct ata_port which is needed in the next patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove device_node_for_nach_child and convert users to corresponding
imported OF API functions.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With of_get_child_by_name from Linux API, we can now convert and remove
of_find_child_by_name.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch converts users of of_tree_for_each_node to recently added
for_eacg_compatible_node helper. Also of_tree_for_each_node is removed
from public OF API.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This imports of_prop_next_u32, of_prop_next_string, and the corresponding
for_property_for_each_ helpers from Linux OF API.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This adds functions to set an array of or a single value for bool,
u8, u16, and u64 properties.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This imports of_parse_phandle_with_args and of_count_phandle_with_args
from Linux OF API. The slightly different of_parse_phandles_with_args
is removed and all users are converted to reflect the API change.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This imports of_property_read_* helpers from Linux OF API to allow
to read all kinds of properties.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This imports of_get_parent, of_get_next_available_child, and
of_get_child_by_name and corresponding helpers from Linux OF API.
of_get_next_child is not imported but implemented as list iterator
instead. Also, of_get_child_count and of_get_available_child_count
are introduced.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This imports of_find_node_with_property and corresponding helpers
from Linux OF API.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This imports of_find_matching_node_and_match and corresponding helpers
from Linux OF API.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This imports of_find_compatible_node and corresponding for_each_compatible_node
helper from Linux OF API.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This imports of_find_node_by_name and corresponding for_each_node_by_name
helper from Linux OF API.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
According to ePAPR 1.1 spec, device tree nodes status can be either
"okay", "disabled", "fail", or "fail-sss". Barebox already has a function
to check for "disabled" nodes, while Linux checks for "okay" or "ok".
To synchronize Barebox and Linux OF APIs, rename of_node_disabled to
of_device_is_available and check for "okay" instead of "disabled" as it
also makes "fail"ed devices unavailable.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Barebox of_find_node_by_path requires a node to be passed as start node
to start searching. Linux OF API does not pass this node and no current
user of it in barebox is passing anything else than the root node.
Therefore, we rename current function to of_find_node_by_path_from and
introduce a Linux OF API compatible of_find_node_by_path that always
passes the current root_node. Also, all current users of that function
are updated to reflect the API change.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To start synchronizing OF API of barebox with linux OF API, this adds
a length pointer to of_find_property. Also all current users of that
function are updated to reflect the API change.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Barebox compares compatible, node names, and property names with strcmp.
Linux by default compares compatible and node names with strcasecmp. To
avoid inconsitencies between Barebox and Linux dts files, we convert to
these default string compare functions.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Current implementation of of_property_write_u32 does free old property
values and allocates new values depending on the size passed. While
copying the new values to the property, corresponding length is not
set. This makes of_property_write_u32 set the length of the new property
values and also adds a API header describing the function.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
of_match_node checks for compatiblity between a set of matches and a
node. Neither the matches nor node pointer are checked for validity.
This adds the required checks to of_match_node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The tran_speed field as decoded from csd is valid in most cases,
so use it to determine the maximum clock we can support. It is
not valid though for MMC highspeed cards, in this case the
csd contains invalid values and we have to set tran_speed explicitly
to the maximum speed. As the values passed into mci_set_clock are
now based on tran_speed we no longer have to limit the rate to
tran_speed in mci_set_clock.
The (intended) effect of this patch is that highspeed MMC cards are
no longer limited to non highspeed rates.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MXS needs some special MXS specific clock types:
- pll
- ref (fractional divider)
- busy divider (divider with additional busy bit to poll on a rate change)
- lcdif (Combined clock out of a fractional divider, a divider and a gate.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On MXS we need to poll the busy bit when changing a clock rate, but only
when the parent clocks are enabled. This exposes the already present
function clk_is_enabled which is suitable for this job.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To get persistent devicenames under /dev/ allow to set the
devicename from the driver instead of using "ata" unconditionally.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX gpio driver doesn't have dependencies, so initialize
it in a core_initcall to have the gpio functions available earlier.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This breaks HSIC and has no good justification why this would
be needed for ULPI.
This reverts commit 2e7d66f526.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some boards need some more tries to successfully detect a phy. This
happens for example on the pcm038. Try up to four times to detect a
phy.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Our driver matches stmpe-i2c and stmpe-spi. It seems the device
we really support is the stmpe1601, so use this one for matching
the devicetree compatible.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Our erase command used to align to eraseblocks when necessary.
This worked well until recently when the m25p80, mtd_dataflash
and cfi flash were added / converted to mtd. This patch aligns
the input to the erase fileoperation to eraseblock boundaries.
Also tested with non uniform flashes with multiple eraseregions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We need ata_id_has_lba48() in another C file, so move
the ATA_ID_* stuff to include/ata_drive.h like in the Linux
Kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In devinfo for the card also print:
- capabilities for host and card
- current bus width
- current clock
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use MMC_CAP_ names instead of MMC_MODE_. This makes it more
clear that these are capabilities of host/card and do not refer
to the current mode. These are in line with the Linux Kernel
except for MMC_CAP_MMC_HIGHSPEED_52MHZ which could be fixed
later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We often encounter the situation where slow devices should not be
probed during startup since probing is slow and maybe unnecessary
for unused devices. With MMC we have the 'probe' device parameter,
for ata we have the same, for USB we have the 'usb' command. Overall
this is not very consistent.
With MMC there is the additional problem that the probe parameter
is attached to the logical device when we often have the information
which physical device we want to probe.
This patch adds a 'detect' callback for devices and adds a command
to detect devices and to list the devices which are actually detecable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This driver should work with some Atheros WiSoCs:
- ar2312, ar2313
- ar2315, ar2316 ...
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It's confusing to set the status of a node to disabled and afterwards
it's invisible. Similarly it's confusing to be able to enable invisible
nodes.
Also print disabled nodes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We already have the possibility to register a mci with a certain
filename to get persistent names. However, the device needed to
find the probe parameter still has the name 'mcix'. This patch
changes this by registering the mci device with the same name
as the filename.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since the info is device specific and not driver specific, attach
the callback to the device. This makes it possible to have a info
callback for a device which does not have a driver attached.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some MMC cards support boot partitions. These are special regions
on the MMC card intended to put a bootloader on.
This patch adds support for these partitions, they are accessible
as /dev/diskx.boot[0|1].
Additionally the partitions can be configured bootable using a
device parameter. This can be used to mark the user area or one
of the boot partitions as bootable.
Since this feature is mostly seen on eMMC cards it is made optional
to lower the size impact for boards which do not have eMMC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This updates the i.MX esdhc divider settings to FSLs U-Boot.
Current timings work fine for SD cards, but not for eMMC.
Although the calculation is fine according to the datasheet and reading from
eMMC works, writing is broken. Atleast on i.MX53/tqma53.
With this patch the result is the same, but uses different divider values to
achieve it.
While at it, replace the udelay with a busy-loop.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This gives the SDHCI specific registers a common name and moves
them to a separate file for use by other SDHCI like drivers.
The SDHCI spec has some 16bit and 8bit registers. The i.MX accesses
these as 32bit registers. These register defines now are named after
the SDHCI registers they combine into one, for example:
SDHCI_HOST_CONTROL__POWER_CONTROL__BLOCK_GAP_CONTROL
is the 32bit version of the SDHCI registers HOST_CONTROL, POWER_CONTROL
and BLOCK_GAP_CONTROL.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If a device does not have bad blocks loop over the eraseblocks
in the driver instead of the core. This allows the mtd_dataflash
driver to erase blocks instead of pages to gain more speed during
erasing. Also the mtd_dataflash driver modifies the erase_info
struct which causes the outer loop in the core to never end.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Many cfi chips support 16 and 8 bit modes. Most important
difference is use of so called "Q15/A-1" pin. In 16bit mode this
pin is used for data IO. In 8bit mode, it is an address input
which add one more least significant bit (LSB). In this case
we should shift all adresses by one:
For example 0xaa << 1 = 0x154
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some parameters may wish to provide some information about their
meaning or possible values. Provide an info callback for parameters.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The fdt reserve map needs address/size values, not address/end values
like accidently done for generating the reserve entry for the dt.
Reported-by: Jürgen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX53 fec claims to be compatible to i.MX25 and i.MX53. In barebox
we do not have to make differences between i.MX25 and i.MX27 though, so
just fall back to i.MX27.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
