- remove mach/silicon.h and include omap?-silicon.h directly
- include mach/omap?-clock.h directly where needed
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Efika MX Smartbook is a i.MX51 based netbook. This patch adds
nearly full support for it including:
- USB
- SD card slots
- Internal SPI NOR flash
- Internal flash PATA drive
- LEDs
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The board variant found on the AT24 EEPROM holds the variant ID that we
can use to identify which expansion board we are running on and thus
which device tree to load and pass to the kernel.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The AT24 found on the expansion boards store the variant of the board it
is soldered onto.
That means that we are that way able to determine what expansion board
is currently plugged in if any. If we can't communicate with the EEPROM,
we just assume that only the CFA-10036 is there.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This EEPROM is found on the expansion boards available for the 10036
module. Since we won't need to do anything fancy except reading/writing
from it, use bitbanging to communicate with it.
This EEPROM will hold mostly the board_id so that we can determine if
there is an expansion board plugged in and what expansion board it is.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The ULPI lines are normally input to the USB port. In order to configure
the ULPI transceiver properly the ongoing transfers must be stopped. This
can be done by configuring the the STP pin as gpio output and drinving
it high.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The smsc911x has a bootstrap pin for detecting an external phy.
Unfortunately this is pulled into the wrong direction on the pcm037
board, so force internal phy with platform data.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for the Garz+Fricke Vincell board. This has
a i.MX53 Processor with 512MB of DDR3 RAM.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In addition, collapse adjacent comment blocks into one and remove
extraneous blank lines.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Pinmuxing was wrong and no GPMI device was created.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we now create the cdev via mtd
This will also simplify sync with linux
to avoid the m25p8000 or m25p00 the cdev is still named name m25p and the
drivers m25p80
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since commit dc9d70e2 the define CCM_PDR4 is called MX35_CCM_PDR4.
sha: Added the same for cupid
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as in the kernel use is_rmii
flags for pinctrl
phy_flags for phylib flags
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as the support atmel mci drivers does not work on rm9200 and we have the
possibility to use it as spi use it
Originally on rm9200 when the interface mci is in SPI mode we use a DataFlash Card
so allow it but if no dataflash card option is enable use as mmc spi.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
on the 9g20 low power version we have a mmc spi as microSD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
on the 9g20 low power version we have a mmc spi as microSD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
on all the cpu module we have a at25 except on the cogent where we have a at45
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The OUI will be 'tml' => 76:6D:6C
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The modules from cogent use a 1.8V nand
And have the mci card detect broken as they use the flash vdd as vdd for the
cd which need > 2V
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
for bootp specify the module version via client_id as
%{BOARD}-%{VERISON}
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The OUI will be 'ron' => 72:6F:6E
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The OUI will be 'ron' => 72:6F:6E
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The OUI will be 'ron' => 72:6F:6E
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes a linker error when PBL_IMAGE=n and DO_LOW_LEVEL_INIT=n.
In this configuration the symbol reset() was present multiple times,
and prevented the barebox image to be linked.
Signed-off-by: Christian Kapeller <christian.kapeller@cmotion.eu>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch remove a superfluous DCD command in TX53-xx30 flash header.
The entry DCD_WR_CMD(0x21c) just duplicates the contents of the last
imx_flash_header_v2 struct member dcd.
Removal of this DCD entry is needed to make the TX53 board boot again
from NAND.
Signed-off-by: Christian Kapeller <christian.kapeller@cmotion.eu>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the phy reset neet to be done before the fec driver is registered
as we accesst the phy at the fec probe time
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Switch to new environment and add the bootscripts needed for mmc. Also,
update defconfig for new environment.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds generic board support (CLEP7212, Linux ARM ID=91)
for CLPS711X-target.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The idea of having /env/init/* scripts was to make the configuration
more flexible and customizable for boards. It turned out though that
people (including myself) do not find the place where they should
change these settings.
So this patch brings back /env/config for defenv-2. The individual
env/init/* scripts are removed and their content is added to
/env/init/config-board. This makes the values from /env/init/config-board
the board specific defaults which can be overwritten in /env/config.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The added complexity of bootargs-ip-* and bootargs-root-* makes
understanding defenv-2 more complicated. remove them and open
code the scripts instead in their users.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
barebox size is 384KiB
and for the official atmel release we need to rootfs at 8M
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
While flash layout may be custom, at least the nand0-device is good to
have.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
now we can flash barebox by itself as the bootstrap need to use pmecc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We support two different board revisions, both of which only differ
in the dcd table, so we can support both in a single binary with the
cost of storing both dcd tables in the binary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This redefines the sdram controller registers as offsets to the base
rather than as absolute addresses. All users are fixed to use the
SoC specific base address.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
board_init_lowlevel is no longer called from generic code, so we can't
just return from in. Instead we have to jump to board_init_lowlevel_return
manually. For the a9m2440 board one case was missed to convert. This
is broken since:
| commit faf7b7af6e
| Author: Jan Luebbe <jlu@pengutronix.de>
| Date: Mon Sep 24 10:18:34 2012 +0200
|
| ARM: give boards control of the reset entry point
|
| On some SoCs (for example AM35xx), the ROM bootloader passes useful
| information in r0 when jumping to barebox.
|
| To avoid overwriting this in the generic reset code, we introduce
| common_reset as a C function and as an assembler macro. This is then
| called form the reset entry point (either in common or in board code).
|
| This patch is based on code by Sascha Hauer <s.hauer@pengutronix.de>.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This moves the known i.MX bootsource settings to a single file
so that the code can be shared. Also we add a enum for the different
boot sources so that it can be used in C Code and not only on the shell.
The pcm038 board is changed to use it instead of digging in the registers
manually.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On i.MX we enable all necessary clocks during startup of the clock
controller driver, so we do not need the register hacking in the drivers
anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The at91sam9260ek has a custom reset function which does the same thing
as the default function. Also it does not define MACH_HAS_LOWLEVEL_INIT
as it should do. Remove the function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
All i.MX SoCs now use the same imx_silicon_revision() function to get
the revision. Add a separate header file for it and a common function
used on all SoCs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds the device id mechanism to the i.MX fec driver and
uses it to determine the fec version. Also adds devicetree
probing support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since we have phylib the phy won't be detected after poweron. It seems
the phy needs some time after reset.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This way you can specify as previously set the dhcp parameter via global.dhcp.xxx
and get the result via global.dhcp.xxx
This is need for the defaultenv-2 to add the bootp suppport.
Use it on defaultenv too to have only one set of var.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The following missed to add a jump to board_init_lowlevel_return for the
phycard pca100 board:
| commit 244198ea8b
| Author: Sascha Hauer <s.hauer@pengutronix.de>
| Date: Sun Jul 8 18:30:42 2012 +0200
|
| ARM boards: Use _text rather than TEXT_BASE
|
| With compressed image support TEXT_BASE will become the base
| address of the uncompressed image. What the boards want instead
| is the base address of the decompressor code or, if not compressed,
| the base address of the uncompressed image. Use _text which is
| the correct one for both cases.
|
| Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes it by adding the jump. Also imx_nand_load_image is directly
called from lowlevel_init.S which fixes compilation with pbl support
enabled.
Tested with both compression enabled and disabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The cfa10036 board file were missing the length parameter when adding
devices. This made barebox crash early in the boot, in the mxs-mci
driver.
Provide the resources lengths in a consistent format.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On some SoCs (for example AM35xx), the ROM bootloader passes useful
information in r0 when jumping to barebox.
To avoid overwriting this in the generic reset code, we introduce
common_reset as a C function and as an assembler macro. This is then
called form the reset entry point (either in common or in board code).
This patch is based on code by Sascha Hauer <s.hauer@pengutronix.de>.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adapt phylib from linux
switch all the driver to it
reimplement mii bus
This will allow to have
- phy drivers
- to only connect the phy at then opening of the device
- if the phy is not ready or not up fail on open
Same behaviour as in linux and will allow to share code and simplify porting.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The FSF address has changed in the past. Instead of updating it
each time the address changes, just drop it completely treewide.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Maxime Ripard
Antony Pavlov
Robert P. J. Day
Wolfram Sang
Vicente Bergas
Jean-Christophe PLAGNIOL-VILLARD
Christian Hemp
Christian Kapeller
Alexander Shiyan
Carlo Caione
Jan Luebbe