7ab0a0a i.MX27: Added helper for setup chipselect control register
added an helper which triggers the following error :
arch/arm/mach-imx/include/mach/imx27-regs.h:243: Error: bad instruction `static inline void imx27_setup_weimcs(size_t cs,unsigned upper,unsigned lower,unsigned addional)'
This patch fix this problem.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixes:
arch/mips/lib/lshrdi3.c:6: warning: no previous prototype for '__lshrdi3'
arch/mips/lib/ashrdi3.c:6: warning: no previous prototype for '__ashrdi3'
arch/mips/lib/ashldi3.c:6: warning: no previous prototype for '__ashldi3'
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fow now use Soft ECC for nand util we add the PMECC.
On-chip and board related peripherals definitions.
Basic implementation for VB board.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds the support for new PIO controller found on some at91sam SOCs.
- more peripheral multiplexing
- more features to configure on a PIO (pull-down, Schmitt trigger, debouncer)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On the sam9x5 series we now support 1 or 2 macb.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- enable MMU
- drop MTD as we do not have nand
- use tlsf
- bootm enable initrd
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
set vendor-id to barebox-at91rm9200ek and the kernel over nfs
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As the mainline kernel does not enable the bootp support by default
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There was no check for BE, so any BITKEEPER(1) iomux configurations
were not being applied.
Signed-off-by: Esben Haabendal <esben.haabendal@prevas.dk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since we do not have ISP1504-related functions, we migrated to ULPI.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because CPU frequency setup called after power initialization,
this call now is not necessary.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
FIXME: part of or no data is written. File copy ends
with message: "atmel_mci@atmel_mci0: command/data timeout"
Signed-off-by: Asen Chavdarov Dimov <dimov@ronetix.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- change the kernel and rootfs locations
- correct the NAND mtd partitions
- fix the DDR RAM location(so BareBox load address)
- expect the root file system type to be UBIFS
Signed-off-by: Asen Chavdarov Dimov <dimov@ronetix.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
What looked like a TO specific hack really is a hack for
older babbage boards. As the babbage code now handles this
correctly we can remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The imx51 lowlevel setup code currently sets the full cpu
speed only for TO3. It turned out that this is not a TO
specific hack but a hack for older babbage boards. Move
the lowlevel init after babbage_power_init() so that we
can remove the hack from the generic i.MX51 lowlevel
function. As this potentially changes the UART clock we
have to flush the console beforehand and call the clock
notifier afterwards.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The previous code assumed pll2 which is correct when we set the
uart parent to pll2 beforehand. The reset default is different
though, so calculate uart parent based on hardware setting.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The image sizes have been hardcoded to 256K. This is inefficient
for smaller images and nonfunctional for bigger images. Calculate
the image size during compile time and use it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
barebox_image_size was calculated wrong when PRE_IMAGE is defined.
In this case _text does not refer to the binary image start. We
have to use TEXT_BASE here.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
when compiling for a imx53 with i2c enabled i got the following error:
drivers/built-in.o: In function `i2c_imx_set_clk':
/home/ggebhardt/repos/ecuv6_bl/barebox/drivers/i2c/busses/i2c-imx.c:282:
undefined reference to `imx_get_i2cclk'
make[4]: *** [.tmp_barebox1] Error 1
make[3]: *** [CMakeFiles/bootloader] Error 2
make[2]: *** [CMakeFiles/bootloader.dir/all] Error 2
make[1]: *** [CMakeFiles/bootloader.dir/rule] Error 2
make: *** [bootloader] Error 2
I copied the following from the corresponding imx51 implementation.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When CONFIG_DEFAULT_ENVIRONMENT_GENERIC is set the Make system
will automatically compile in defaultenv/ into the environment. Some
boards explicitely add this path again in their defconfig which is
not needed. Remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
imx27_add_mmc0 really registered SDHC2. Fix this by adding a
imx27_add_mmc1 and use this in the pca100 board file. Also add
imx27_add_mmc2 helper for register SDHC3.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove GPIO2.6 setup from lowlevel_init. It can be defined in board
initialization code if it necessary.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To reduce the size of the MLO we have to activate thumb-2 support.
Otherwise the board will not boot.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a OMAP4 specific GMPC nand config for pcm049 and phyCARD-A-XL2 to increase
performance. Also add the possiblility to pass a board GPMC nand config.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The image built with pcm038_defconfig is >256k so increase
the size of the barebox partition.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
drop kernelimage_type bootm now boots all of them.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support for omap4 based Phytec phyCARD-A-XL2 board
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- use tslf
- bootm: enable oftree and uimage support
- enable mmu support
- drop cfi support (no nor on the board)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
update fancy prompt to be the same as the other Atmel board
use the same feature on 9g10ek and 9261ek
- use tlsf
- enable MMU
- set max size to 256KiB
- bootm: add initrd support
- nand: drop non used hw ecc and oob device
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
- set max size to 256KiB
- enable MMU
- bootm: enable oftree and initrd support
- nand: drop non used hw ecc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
most of the board does not have a nor soldered
update the nand partition table to boot from nand with bootstrap
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
If we want to trap the processer in the exception vectors
we have to use unconditional branch instructions. I don't
know what I thought when using bne :-/
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This shrinks the resulting binary size by ~25%. Exceptions
are still handled in arm mode, so we have to explicitely
put .arm directives into the exception code. Thumb-2 mode
has been tested on i.MX51 Babbage board.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add Mitac MioA701 board initial support.
The support provides basic boot and :
- a console over USB (serial gadget).
- the SD card support
- the MTD docg3 support
- the LCD support
Add a check in the default environment for a barebox.env
file on the first partition (FAT). If the file exists,
source it instead of the normal boot procedure.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We used to get the runtime offset of the board_init_lowlevel_return
by doing a &board_init_lowlevel_return. This does not work in thumb-2
mode, so use a separate linker section for this function instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Traditionally U-Boot and barebox have the exception vectors at
the start of the binary. There is no real reason in doing so,
because in the majority of cases this data will not be at 0x0
where it could be used as vectors directly anyway.
This patch puts the vectors into a separate linker section and
defines an head function which is placed at the start of the
image instead. Putting this in a separate function also has
the advantage that it can be placed at the start of images
which require an additional header like several Freescale i.MX
images. As the head function contains the barebox arm magic
those images can now also be detected as barebox images.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- this is taken from freescale-mx35-3-stack/3stack.c and allows
this board to run Freescale's kernel which relies on the system
revision to configure the correct PMIC.
- On rev0 boards (with DA9053), the log is :
detected i.MX53 rev 2.1
MCIMX53-START board 1.0
On newer boards (rev A or B with MC34708), the log is :
mc34708-i2c@mc34708-i2c0: MC34708 ID: 0x0014
detected i.MX53 rev 2.1
MCIMX53-START-R board 1.0 rev B
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
and register mc34708 which is present on MCIMX53-START-R board
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this allows I2C to work on boards which don't have external pull up
(like LOCO board)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To be able to use the sandbox with fat filesystem support unaligned.h is needed.
It tries to be general in selecting little endian or big endian on a gcc macro.
Signed-off-by: Lars Poeschel <lars@kiwigrid.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixing this typo lets the barebox for pm9261 to be build.
Signed-off-by: Asen Chavdarov Dimov <dimov@ronetix.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add CCCR bits definition for PXA SoC, so that the bootloader
can setup a stable core clock frequency, which is not the
initial reset clock, as required by Intel's PXA27x Processor
family developer's guide, chapter 3.5.5, table 3.7 (clock
frequencies).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add standard GPIO routings for LCD panels, taken from linux
kernel.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As pxafb can rely on a PWM to control backlight, and because
driver dependencies are hard to deal with, remove automatic
enable of PXAFB on probe.
The user should in its environment do a :
- fb0.enable=1
This way, the PWM has been probed and is ready to work, and
the pxafb backlight control works.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add PXA embedded pulse width modulator support. The PWM can
generate signals from 49.6kHz to 1.625MHz.
The driver is for pxa2xx family. The pxa3xx was not handled yet.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current message indicating that SD card isn't
mounted is misleading if the card has only one
partition.
Updated the message to indicate that mounting
the specific partition failed.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some variants of the i.MX53 do not allow to run at 1GHz, so
pass a cpu frequency parameter to the lowlevel init function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Whether the controller works in 8bit mode is not only dependent
on the controller but also on the board having wired up 8 data
lines, so put a capabilities field in platform data.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove what is an apparently valueless Kconfig variable HAS_OMAP_NAND.
A search of the entire source tree shows:
$ grep -r HAS_OMAP_NAND *
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig:config HAS_OMAP_NAND
arch/arm/configs/phycard_a_l1_defconfig:CONFIG_HAS_OMAP_NAND=y
$
where the definition of that variable is simply:
config HAS_OMAP_NAND
bool
so it seems pretty clear it can be removed as nothing is using it.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Without the proper OMAP3 or OMAP4 dependency directives, you get the
wrong list of choices displayed based on which OMAP variant you pick.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
At least ARM allows us to dump the stack, but we currently
have no prototype for this. Add a dump_stack prototype and
provide a static inline function for architectures without
stack dump support. Also, call dump_stack() in panic() to
provide more information in the case of a panic.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
hang() only outputs 'reset the board' whereas panic
can be passed a string which we can use to output
some more information what is happening.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Otherwise the kernel would not register the nand partitions.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Extend DCD table and low level init routines. Add barebox SDRAM
device. Also, fix the memory size for bank 0 to 128MB. It was
accidently changed to 124MB here:
commit f928efa818
Author: Sascha Hauer <s.hauer@pengutronix.de>
Date: Tue Jul 19 09:58:32 2011 +0200
add a add_mem_device function
Add a helper function for boards to register their memory
devices. This makes the board code smaller and also helps
getting rid of map_base and struct memory_platform_data.
And switch all of the memory to it
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this allow to check we do not exceed the size of the SRAM as example
introduce BAREBOX_MAX_BARE_INIT_SIZE the maximum size of bare_init
this will allow your bare_init will fit in SRAM as example
ARCH can overwrite it via ARCH_BAREBOX_MAX_BARE_INIT_SIZE
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adding overlay support for phyCORE-i.MX35.
Also move the TEXT_BASE to leave enough space for the overlay image
at the end of the RAM.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adding overlay support for i.MX3 sdc.
Foreground channel only works when background is also enabled.
The foreground video mode is always the same as the background.
Also added alpha command to set the alpha value of the foreground.
Tested on a phyCORE-i.MX35.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added num_modes to all imx_ipu_fb_platform_data structs.
Removed defines for pcm043 to choose display.
We may switch this during runtime now.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Make support of multiple video modes possible for i.MX3 boards.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
board_init was moved to pure_initcall. broken since:
commit 0adce7ec68
Author: Sascha Hauer <s.hauer@pengutronix.de>
Date: Sun Jan 15 21:11:17 2012 +0100
ARM omap3: move board_init to pure_initcall
board_init initializes the mux and sdram. For both there is no
need to configure this so early. Move the code to a pure_initcall
and remove the surrounding unneeded code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
since commit 494a12f703
platform lowlevel init was moved to mach-omap.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
since commit ae2ac15105
a_init was renamed to omap3_core_init and called from board code.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
board_init is now called omap3_board_init. broken since:
commit 494a12f703
Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Date: Sat Jan 14 15:51:05 2012 +0100
omap3: move platform lowlevel init to mach-omap
this will allow to switch omap3 to standard organisation
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This function consists of only inline asm statements, so
use assembly in the first place. Also makes sure that the
function is compiled in arm mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
No need to do this so early. We can't print anything right
now anyway, so there is no need to setup vectors.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
There is no need to call a_init before relocation, so rename
the function to omap3_core_init and call it from board code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
board_init initializes the mux and sdram. For both there is no
need to configure this so early. Move the code to a pure_initcall
and remove the surrounding unneeded code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
Setting up the clocks does not work when the stack is in SDRAM.
Moving the stack to SRAM allows us to do the lowlevel clock setup
later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
The X-loader startup relocates to SRAM anyway, so there
is no need to be runnable from flash for the clock code.
This config is disabled in all defconfigs anyway, so remove
it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
this will allow to create it's own env/config
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to create it's own env/config
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to create it's own env/config
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to switch omap3 to standard organisation
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
in commit commit f60f6c58e
atmel_mci: check for device id we use to address the right slot
the driver use the dev_id to detect the slot which is wrong on 9263 as we have
2 devices with 2 slots
use slot_b paramter to specify the slot as done in linux
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to configure the nand as example
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When CONFIG_OMAP_BUILD_IFT is selected, the
target image name was set to "barebox.bin.ift".
This file must be renamed "MLO" before it can
be used on the SD card.
Make this as default behavior.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Enable the flag HAVE_NOSHELL to allow first stage
bootloader to be built for this board.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The base address passed for device "omap-hsmmc" was
incorrectly passed as OMAP_I2C1_BASE and the base
address for device "i2c-omap" was hardcoded to
0x4809C000 which, in fact, refers to OMAP_MMC1_BASE.
Similarly, in call to add_usb_ehci_device(), addition
is not required if right base address is used.
In fact, 0x48064700 (used as base in the addition)
falls in the OHCI Address space.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The config option CONFIG_GPMC is renamed to
CONFIG_OMAP_GPMC as result of this commit:
819f416b86
Still, sources continue to use CONFIG_GPMC.
Fix it.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
use ds3 for heartbeat and ds5 for dfu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
on 9269 and 9g20 the sram are mirrored at then of the bank so we can join them
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Without num_modes the imx fb driver won't work. Specify this
in the boards and also bail out in the driver when num_modes
is unspecified.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Using SSP1 since this is the default configuration.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this was introduced in "6b3e01a arm: eukrea: Fix compilation warning"
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
enable serial and dfu at the same time
senario if the usb device is plugged and the BP is not pressed at boot time
during 5s the usbserial will be enable
disable zlib support to fit in the 256K
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The lowlevel init function was a 1:1 copy from the babbage
baord, so it should be safe to switch to the generic C
lowlevel init.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Eric Benard <eric@eukrea.com>
Reimplement the code from lowlevel.S in C. It is run
from SDRAM anyway, so we can safely do this initialization
in a regular barebox environment instead in Assembly.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- move code which can be shared between i.MX53 and i.MX51
to a common file
- rename mx53_init_lowlevel to imx53_init_lowlevel
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
a) use the more CPU specific S3C* macro names
b) move the register description out of the way, as more recent CPUs using a
different layout and more features
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Keep common code in the MACH instead of re-inventing it in each platform.
Also use S3C* macros for all memory related register.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The UART is one of the units which differs only slightly inside the S3C family.
Prepare this driver to share it with more recent CPUs.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
After separation and after all S3C macros are now present, change the driver
to be more generic for future additions.
The timer registers in the S3C24XX family are only 16 bit wide. But these
registers can be read and written in a 32 bit manner. This is important to share
code with more recent CPUs which comes with 32 bit registers.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most members of the S3Cxxxx family share similar timer units. But they are
not really register compatible. To reflect this, use a separate name space for
the S3C family.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch just move the clocksource functions out of the generic.c source file
to handle it on a per CPU base later on.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are major differences in the clock tree of the S3C24xx family and the
more recent CPUs of the S3C family. Keep the S3C24XX clock routines separate to
avoid an ifdef hell. But also use generic function names to be able to
share drivers among the S3C family.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This LCD driver is for the LCD controller in the S3C2410/S3C2440 CPUs only.
Change its name to reflect its usage and free the way to add LCD controller
drivers for more recent Samsung CPUs.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The aready existing NAND controller driver in Barebox is for the S3C24XX family
only. Change the name of the file to reflect this fact (and free the way to add
more recent Samsung NAND controllers)
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Start with renaming files to share them in the S3C CPU family,
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The S3Cxxxx family consists of ARMv4, ARMv5 and ARMv6 types of CPU cores. The
S3C24xx sub family is only one of it. To be able to handle all CPUs in one mach
directory, use a more generic name for it.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds basic support for the mx28-evk board. Debug UART, MMC and FEC
have been successfully used.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Recent gcc generates code with unaligned access when architecture
supports it. Setting A bit unconditionally causes data-aborts on such
code rendering barebox unusable.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When executing 'bl' in inline assembler, the 'lr' register must be
marked as clobbered too.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In this generic configuration, the board can be run in the
or1ksim simulator with the linux configuration file using
the UART to print the console.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
OpenRISC is the original flagship project of the OpenCores community.
This project aims to develop a series of general purpose open source
RISC CPU architectures.
A team from OpenCores provided the first implementation, the OpenRISC
1200, written in the Verilog hardware description language.
Even though I should have created an mach-or1200 directory, it is not
necessary for now. The OpenRISC 1200 CPU is the only one available and
it will be for some time.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
detect it at boot time
if the user button is pressed 5s and the vbus is 1 start the dfu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
drop irq id and rebase instead of of offset
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this device controller is present on rm9200/9260/9g20/9261/9g10/9263
the 9g45 use an other IP
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support the setup of the mmc voltage, when booting OMAP4 with twl6030
from nand.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added i2c support for omap4. Tested on pcm049.
Driver based on linux kernel implementation.
Also added a shift to access 16-bit registers
to make support for OMAP730/850 possible.
If accessing a non existing slave the bus will go into arbitration mode.
It's unable to recover from it.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a function to remap an IO range into a virtual addresses
range. This is particulary usefull for the few devices
mapped at physical address 0, as the MTD boot devices.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The device resources are much smaller, the resource mechanism
revealed this because of overlapping devices.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The icache command is unused. Instead of adding it to compilation
again, remove it as the cpuinfo command provides the same information.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
configure BP4 and BP3
use BP4 to start DFU mode at boot
if BP4 is pressed at boot time and maintain at least 5s the dfu is started
otherwise we boot normaly
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
by default boot from nand with the bootstrap as first stage
update the smc config for 9g20-ek
switch to defaultenv
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that we have a bootm command which boots everything we can
simplify the defaultenvironment. We can call bootm on every
image type and can remove the kernelimage_type variables.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This switches the bootm code to the new uimage code. Also
bootm can now handle other types of images than uImages.
Currently the only architecture making use of this is
arm which allows to boot zImages, raw images and barebox
images.
I intended to make a more bisectable series from this but
I failed becuase there are many dependencies and no matter
how I tried the patches grew bigger and and bigger. So I
decided to put this all in a single patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
whoever calls this function is not necessarily aware of a struct
image_data, so remove the dependency from the function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support for the old DM9000E device is now part of the new dm9k.c driver. So,
remove the old driver source and switch all users to the new driver.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The device resources are much smaller, the resource mechanism
revealed this because of overlapping devices.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
on at91sam9 you need to shutdown the sdram/ddr controler before reseting
when you boot from nand
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Newer pcm038 are populated with a PC28F256P30BFE NOR-Flash.
This flash requires different CS values.
The values also work with older NOR-Flashes.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add all available video modes to the framebuffer. devinfo fb0
shows the available modes. We can select a mode now.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
a temporary setting was inserted in the default env by error
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
without this, the pins seems to be opendrain and thus the LCD signals
are not properly driven leading to wrong colors on the screen.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add the platform data for MMC/SD card host on the PXA SoCs.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add mmc clock frequency reader. Easy as MMC host controller
is constant, while the clock between host and card is
settable.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to execute a program of the host from barebox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adapt mainline kernel pxa27x_udc driver to barebox :
- remove function header comments as they are in mainline
- test it with serial gadget
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The core support was brought by Marc and Sascha.
The cache choice was fixed by Luotao Fu.
Some gpio and devices addons were provided by Robert.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Barebox cannot boot the recent mainline Linux kernels for the
i.MX21ADS board anymore when using TFTP, because the heap is too
small.
This is solved by increasing the heapsize to 5Mbyte.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
All handlers used to just relocate the image without any checks, so
we are doomed if we write outside of SDRAM or will overwrite ourselves.
Move the relocation up to the generic part where we have a chance
of catching these issues.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that the arch_number and system_rev variables can be set from
the environment we don't need the old bootm command line switch
mechanism anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
arch_number is currently exported to the environment but not read back
on boot time which is rather confusing. system_rev and system_serial
are not exported to the environment but can be set in board specific
code.
This patch exports all these variables to the environment and reads them
back on boot time. All variables get a armlinux_ prefix, so the
arch_number environment variable gets renamed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We never had interrupt support in barebox and we have no plans to
add interrupt support. Even if we do I doubt the current fragments
of irq support are helpful, so remove them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Rename create_section into create_sections, as the function
is used to create multiple sections, and in particular it
creates the 4096 sections of 1MBytes to have a 1:1 flat
mapping of the 4GBytes address space.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
These symbols where defined for the A9M2440 platform. Rename them to the
platform they now belong to.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Linux kernel says (spi.h) :
* All SPI transfers start with the relevant chipselect active. Normally
* it stays selected until after the last transfer in a message. Drivers
* can affect the chipselect signal using cs_change.
*
* (i) If the transfer isn't the last one in the message, this flag is
* used to make the chipselect briefly go inactive in the middle of the
* message. Toggling chipselect in this way may be needed to terminate
* a chip command, letting a single spi_message perform all of group of
* chip transactions together.
*
* (ii) When the transfer is the last one in the message, the chip may
* stay selected until the next transfer. On multi-device SPI busses
* with nothing blocking messages going to other devices, this is just
* a performance hint; starting a message to another device deselects
* this one. But in other cases, this can be used to ensure correctness.
* Some devices need protocol transactions to be built from a series of
* spi_message submissions, where the content of one message is
* determined by the results of previous messages and where the whole
* transaction
* ends when the chipselect goes intactive.
In other words, cs_change changes the default chipselect *behavior*.
Support of cs_change is necessary to implement the mci spi driver.
This patch also fix few things:
Passing the bus number to the brand new master device.
Disable chipselect during master->setup.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
now we can detect the host build from gcc macro
and cross compile the sandbox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Loïc Minier <loic.minier@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
nand.c issues a warning when imx_nand_set_layout is
empty. We don't need this function on i.MX53, so
silence the warning.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The S3C2440 CPU comes with an internal OHCI the generic part of
Barebox already supports. Just add the missing part.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The size is being calculated after changing to another section, which
gives error with gcc 4.6:
AS arch/x86/lib/traveler.o
/tmp/ccP0z8xx.s: Assembler messages:
/tmp/ccP0z8xx.s: Error: .size expression for real_to_prot does not evaluate to a constant
/tmp/ccP0z8xx.s: Error: .size expression for prot_to_real does not evaluate to a constant
make[1]: *** [arch/x86/lib/traveler.o] Error 1
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently, there are multiple definitions of run_shell()
for each board that can be build in "xload" configuration.
Now there is only one function used by all boards.
The functions defined in xload.c are used only when "xload"
configuration used; but it gets compiled unconditionally.
This has been fixed as well.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
let the linker to provide the basic linker script
just insert the commands and initcalls before the .rodata section
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
today we have the same linker script in board and lib
and only the board linker script is used
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If the user has parsed a tree, we start Linux using the
device tree, otherwise we use the traditional ATAG
mechanism.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When building sandbox with ccache, one would hit warnings such as:
warning: 'struct mmsghdr' declared inside parameter list
on random files; a way to reproduce this issue is to build a simple
file doing just:
#include <sys/socket.h>
int main(void) {
return 0;
}
gcc -Wall -P -c -o foo foo.c
But actually the -P flag is only useful when generating non-C files,
such as linker scripts in the case of barebox. Removing the -P flag
from all the gcc invocations, except when generating .lds files makes
the warning go away. It turns out that this is what
linux/scripts/Makefile.build also does nowadays.
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Running the 'bootz' command always fails with
could not read <some file>
due to wrong usage of pointers and structures. This is the second try to fix
the 'bootz' command. At least on my target it is now be able again to load a
kernel without any error.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Running the 'bootz' command always fails with
could not read <some file>
due to it loads only a size of a pointer, instead of the size of the expected
header structure.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch remove those warnings in nios2 drivers:
include/io.h:7:5: warning: "__BYTE_ORDER" is not defined
include/io.h:7:21: warning: "__BIG_ENDIAN" is not defined
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Contrary to other Atmel boards, the AT91SAM9M10G45EK board file only
describes the case where NAND is used as the storage for Barebox and
its environment. Therefore, it makes sense to enable the Atmel NAND
driver in the default configuration for this board.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The environment partition was overlapping the Barebox partition in
those three Atmel boards. Saving the environment resulted in the
Barebox being overwritten.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We switched to resources recently and the nand controller
of the i.MX53 needs two of them, so fix the helper in the
same way as the i.MX51
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds lowlevel (AIPS, PLL, L2) initialization for i.MX53 boards.
This is a direct transcription of Freescales U-Boot assembler code
with the exception that we initialize PLL1 with 1000MHz and assume
that all necessary voltages are already adjusted when we arrive here.
It must be explicitely called from the boards so a board is free to
do it's own initialization. However, boards should use this code
and make it more configurable if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixes alignment for the "System Type" menu entry.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard
Sascha Hauer
Alexander Shiyan
Jean-Christophe PLAGNIOL-VILLARD
Esben Haabendal
Allan Heldgaard
Esben Haabendal
Asen Chavdarov Dimov
guenter.gebhardt@rafi.de
Teresa Gámez
Jan Weitzel
Michael Grzeschik
Robert Jarzmik
Lars Poeschel
Sanjeev Premi
Robert P. J. Day
Marc Kleine-Budde
Roman Fietze
Juergen Kilb
Wolfram Sang
Juergen Beisert
Enrico Scholz
Franck Jullien
Alexander Aring
Daniel Mack
Christian Hemp
Antony Pavlov
Robert Jarzmik
Jaccon Bastiaansen
Lucas De Marchi
Fabio Estevam
Loïc Minier
Thomas Petazzoni
Alexander Shiyan
Robert Schwebel