this allow to save between 100 to 300 bytes
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
with:
- led
- USB Device
- uart
- net
- mmc
- MMU
dfu support
detect it at boot time
if the user button is pressed 5s and the vbus is 1 start the dfu
otherwise the vbus is 1 start usb serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently, both SDHC clock source is PLL3. We can raise clock
for SDHC driver by change source from PLL3 to PLL2.
Below, is debug ouputs with old and new settings.
Detection (PLL3):
set clock: wanted: 400000 got: 375000
Operation (PLL3):
set clock: wanted: 25000000 got: 18000000
Operation SD4.0 (PLL3):
set clock: wanted: 52000000 got: 27000000
Detection (PLL2):
set clock: wanted: 400000 got: 399639
Operation (PLL2):
set clock: wanted: 25000000 got: 23750000
Operation SD4.0 (PLL2):
set clock: wanted: 52000000 got: 41562500
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
fixes
arch/arm/mach-samsung/Kconfig:95:warning: config symbol defined without type
Until we actually have board support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Traditionally we call __mmu_cache_flush in early startup. There
is a problem with armv7 and hierarchical caches though, on these
systems __mmu_cache_flush uses the stack. Appearantly this was
seldomly a problem, because most of these systems have a ROM
bootloader which sets up some stack, but on a special i.MX6 system
this failed badly. We should not have to flush caches here. Every
sane system should pass control to the bootloader without stale
entries in the caches *), so it should be a safe assumption that the
cache flush can be removed.
Since __mmu_cache_flush is not called from early code anymore we can
also move it to the regular text section.
Be brave and give it a try.
*) omap3 seems to be a exception to this, but this has a cache flush
in arch_init_lowlevel already
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added support for CompactFlash cards for PCM970 development board via
PCMCIA window.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Register GPIO7 as heartbeat LED, same as in the linux kernel.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add i2c-omap and twlcore driver to panda board.
(Based on similar patch for pcm049).
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If barebox is not used as the MLO, then it crashes during boot
with the below error message:
Board: Texas Instrument's Panda
PandaBoard Revision: 003
omap-hsmmc@mci0: registered as mci0
unable to handle paging request at address 0x4a064010
pc : [<8f01e820>] lr : [<8f0049a0>]
sp : 8cffff80 ip : 00000016 fp : 00100103
r10: 00000000 r9 : 00000ae7 r8 : 4030b76c
r7 : 40300200 r6 : e28f8028 r5 : 0000003e r4 : 00000000
r3 : 4a064000 r2 : 00000014 r1 : 00000001 r0 : 00000001
Flags: nzCv IRQs off FIQs off Mode SVC_32
[<8f01e820>] (panda_devices_init+0x17c/0x1e0) from [<8f006300>] (start_barebox+0x18/0x10c)
[<8f006300>] (start_barebox+0x18/0x10c) from [<8200006c>] (0x8200006c)
[<8f021248>] (unwind_backtrace+0x0/0x98) from [<8f011a00>] (panic+0x28/0x3c)
[<8f011a00>] (panic+0x28/0x3c) from [<8f02171c>] (do_exception+0x10/0x14)
[<8f02171c>] (do_exception+0x10/0x14) from [<8f021784>] (do_data_abort+0x2c/0x38)
[<8f021784>] (do_data_abort+0x2c/0x38) from [<8f021470>] (data_abort+0x50/0x60)
This is because the USBHOST module is not enabled. The module enable
is is normally done in mach-omap/xload.c which never gets called.
Since we're configuring the USBHOST CLKCTRL register in the board file
anyway, we might as well explicitly enable the module in the same place.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This switches the pcm038 board to the new environment template and
does the necessary defaultconfig adjustments. Additionally it disables
UBI support as the pcm038 image is getting bigger and bigger and UBI
seems to be the most unused big (in size) feature.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this patch also cleans the source by putting in device_init
the code which is actually in console_init and has nothing
to see with the console.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
else USB device doesn't work as the hardware fix is present on the
boards
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch reflects real naming of SPI by Freescale.
We have two ECSPI channels and one CSPI.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Among other things the power initialization also turns on power
for the ethernet phy, so register the fec after power init.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a check to verify if /barebox.BIP0 exists, and if so,
unlock the protection area, flash barebox, and reprotect the
area.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To speed-up linux kernel loading, switch the PXA cpu to the
maximum allowed frequency (520 MHz). This improves the load
time from several seconds to less than a second from the
MTD.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In order for barebox to be functional, the docg3 DPS1 has to
protect barebox from writes, and have its embedded IPL coded
to load barebox (as barebox is the SPL).
Add a raw DPS1, which :
- protects the area from block 6 to block 123
This is DPS1 + barebox + barebox-logo
- encodes the 2048 bytes IPL
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Make the autoboot work :
- if no USB cuable is plugged, continue directly to
autoboot
- if an USB cable is plugged, wait for 3 seconds for
any input on the USB serial gadget, and if none
happens, continue to autoboot linux kernel
- else interrupt autoboot and interact on barebox
console
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Recent evolutions of linux kernel's drivers for docg3 chip,
ie. it's renaming for mtdparts option, is handled by this
patch.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This got broken while updating the iomux definitions from the
kernel. Since then the PMIC did not work anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The value already is set by calling gpio_direction_output.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Ok, I assume this should go into separate series. It fits both S5PV210 and S3C6410.
This adds support for S3C and S5P architectures (all of my knowledge) to the
serial driver. Since the only difference between them is in clock handling,
this is moved to an arch-dependent separate function.
Most modern architectures should define S3C_UART_HAS_UBRDIVSLOT and S3C_UART_HAS_UINTM.
This adds support for most
Signed-off-by: Alexey Galakhov <agalakhov@gmail.com>
Signed-off-by: Juergen Beisewrt <kernel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Actually ISP1504 ULPI chip are installed on PCM970 development board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We currently use the environment variable 'bootargs' to get the
Linux bootargs. This patch allows for a more flexible bootargs
generation using global variables. With it the Linux bootargs
are concatenated from multiple variables. This allows to replace
parts of the bootargs string without having to reconstruct it
completely.
With this bootargs can be constructed like:
global linux.bootargs.base="console=ttyS0,115200"
global linux.bootargs.ip="ip=dhcp"
global linux.mtdparts="physmap-flash.0:512K(nor0.barebox),-(root)"
This will then automatically be combined into a kernel bootargs
string during boot.
If the 'linux.bootargs.' variables are all empty the old standard
'bootargs' way will be used.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some devices need to be moved to the PCM970 source file later, because
in fact these devices are not installed on the main unit PCM038.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Power and frequency should be setup before initialize other devices.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Barebox cannot boot the recent mainline Linux kernels for the
i.MX21ADS board anymore when using TFTP, because the heap is too
small.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The MD2 add:
- uart 2
- ethernet
- usb
- spi
- i2c
so fix just add uart and ethernet
update defconfig
always enable the motherboard and drop the SHA256 support (to fix in the
256KiB).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Also definition can be modified in arch/arm/boards/pcm043/lowlevel.c,
but I am not sure is we can call imx_silicon_revision() from
board_init_lowlevel().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So we can use it for dhcp request too.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to understand what happened.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So we can use it for dhcp request too.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Supported devices:
- nand
- ethernet
- mmc0, mmc1 (on stk5v3 development board)
- led (on stk5v3 development board)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
barebox can startup with I-cache enabled, so to be on the safe
side we should invalidate the I-cache before jumping to a binary
we just copied in place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Compile fixes unknown symbol 'mxs_ocotp_read' for tx28 defconfig. Since
the vendor stores the MAC address in OCOTP, we always want this driver.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When a oftree is concatenated,the zImage is bigger than the size specified in
the zImage header. Detect it and copy it too.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Android Image contains 3 components and params
- kernel
- initrd
- second stage (optional)
- tags addr
- bootargs
In fast boot the initrd is mandatory, in barebox we are less restrictive
use the initrd only if present
add to env params:
aimage_noverwrite_bootargs
Disable overwrite of the bootargs with the one present in aimage
aimage_noverwrite_tags
Disable overwrite of the tags addr with the one present in aimage
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Without yet adding in the underlying code, extend the revision
checking code to return additional values for PandaBoard ES boards.
Much of the code was taken close to verbatim from U-Boot.
compile tested, and confirmed that this code behaves identically to
the original panda configure and build for the three pandas i have:
* Rev A2 (boots)
* Rev EA3 (boots)
* Rev B1 ES (no output)
so while there's still work to be done, this at least represents the
necessary infrastructure to start *recognizing* panda ES boards.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
add oftree partition to store the dtb
set the oftree location
use a zImage by default now
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This means using an uint64_t instead of a struct pad_desc which allows
us to change pad settings using logic operations. Also with this we
can more easily keep the iomux tables in sync with the kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Also renamed config option name to MFD_MC13XXX.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
by default we boot the same way as before
The menu add interactive interface to choice boot, reset or update the system.
We still can access the shell.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pcm027 is a PXA270 based Phytec phyCORE board.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Boot zImage and update nand partition layout to store the oftree.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Gregory HERMANT <gregory.hermant@calao-systems.com>
Boot via nfs instead of tftp and zImage.
Update nand partition layout to store the oftree.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Gregory HERMANT <gregory.hermant@calao-systems.com>
Read-only support for now to get MAC addresses.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this patch fix the following warnings :
arch/arm/mach-at91/at91sam9g45_devices.c:305:3: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]
arch/arm/mach-at91/at91sam9g45_devices.c:309:3: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
e62edd3 mxs: Fix support for BITKEEPER() macro
added this macro in iomux-imxc.c but the macro is not present
in the i.MX23 case. Adding it in iomux-imx23.h fix both
imx23evk_defconfig and chumbyone_defconfig
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
7ab0a0a i.MX27: Added helper for setup chipselect control register
added an helper which triggers the following error :
arch/arm/mach-imx/include/mach/imx27-regs.h:243: Error: bad instruction `static inline void imx27_setup_weimcs(size_t cs,unsigned upper,unsigned lower,unsigned addional)'
This patch fix this problem.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fow now use Soft ECC for nand util we add the PMECC.
On-chip and board related peripherals definitions.
Basic implementation for VB board.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds the support for new PIO controller found on some at91sam SOCs.
- more peripheral multiplexing
- more features to configure on a PIO (pull-down, Schmitt trigger, debouncer)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On the sam9x5 series we now support 1 or 2 macb.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- enable MMU
- drop MTD as we do not have nand
- use tlsf
- bootm enable initrd
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
set vendor-id to barebox-at91rm9200ek and the kernel over nfs
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As the mainline kernel does not enable the bootp support by default
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There was no check for BE, so any BITKEEPER(1) iomux configurations
were not being applied.
Signed-off-by: Esben Haabendal <esben.haabendal@prevas.dk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since we do not have ISP1504-related functions, we migrated to ULPI.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because CPU frequency setup called after power initialization,
this call now is not necessary.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
FIXME: part of or no data is written. File copy ends
with message: "atmel_mci@atmel_mci0: command/data timeout"
Signed-off-by: Asen Chavdarov Dimov <dimov@ronetix.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- change the kernel and rootfs locations
- correct the NAND mtd partitions
- fix the DDR RAM location(so BareBox load address)
- expect the root file system type to be UBIFS
Signed-off-by: Asen Chavdarov Dimov <dimov@ronetix.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
What looked like a TO specific hack really is a hack for
older babbage boards. As the babbage code now handles this
correctly we can remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The imx51 lowlevel setup code currently sets the full cpu
speed only for TO3. It turned out that this is not a TO
specific hack but a hack for older babbage boards. Move
the lowlevel init after babbage_power_init() so that we
can remove the hack from the generic i.MX51 lowlevel
function. As this potentially changes the UART clock we
have to flush the console beforehand and call the clock
notifier afterwards.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The previous code assumed pll2 which is correct when we set the
uart parent to pll2 beforehand. The reset default is different
though, so calculate uart parent based on hardware setting.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The image sizes have been hardcoded to 256K. This is inefficient
for smaller images and nonfunctional for bigger images. Calculate
the image size during compile time and use it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
barebox_image_size was calculated wrong when PRE_IMAGE is defined.
In this case _text does not refer to the binary image start. We
have to use TEXT_BASE here.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
when compiling for a imx53 with i2c enabled i got the following error:
drivers/built-in.o: In function `i2c_imx_set_clk':
/home/ggebhardt/repos/ecuv6_bl/barebox/drivers/i2c/busses/i2c-imx.c:282:
undefined reference to `imx_get_i2cclk'
make[4]: *** [.tmp_barebox1] Error 1
make[3]: *** [CMakeFiles/bootloader] Error 2
make[2]: *** [CMakeFiles/bootloader.dir/all] Error 2
make[1]: *** [CMakeFiles/bootloader.dir/rule] Error 2
make: *** [bootloader] Error 2
I copied the following from the corresponding imx51 implementation.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When CONFIG_DEFAULT_ENVIRONMENT_GENERIC is set the Make system
will automatically compile in defaultenv/ into the environment. Some
boards explicitely add this path again in their defconfig which is
not needed. Remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
imx27_add_mmc0 really registered SDHC2. Fix this by adding a
imx27_add_mmc1 and use this in the pca100 board file. Also add
imx27_add_mmc2 helper for register SDHC3.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove GPIO2.6 setup from lowlevel_init. It can be defined in board
initialization code if it necessary.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To reduce the size of the MLO we have to activate thumb-2 support.
Otherwise the board will not boot.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a OMAP4 specific GMPC nand config for pcm049 and phyCARD-A-XL2 to increase
performance. Also add the possiblility to pass a board GPMC nand config.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The image built with pcm038_defconfig is >256k so increase
the size of the barebox partition.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
drop kernelimage_type bootm now boots all of them.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support for omap4 based Phytec phyCARD-A-XL2 board
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- use tslf
- bootm: enable oftree and uimage support
- enable mmu support
- drop cfi support (no nor on the board)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
update fancy prompt to be the same as the other Atmel board
use the same feature on 9g10ek and 9261ek
- use tlsf
- enable MMU
- set max size to 256KiB
- bootm: add initrd support
- nand: drop non used hw ecc and oob device
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
- set max size to 256KiB
- enable MMU
- bootm: enable oftree and initrd support
- nand: drop non used hw ecc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
most of the board does not have a nor soldered
update the nand partition table to boot from nand with bootstrap
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
If we want to trap the processer in the exception vectors
we have to use unconditional branch instructions. I don't
know what I thought when using bne :-/
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This shrinks the resulting binary size by ~25%. Exceptions
are still handled in arm mode, so we have to explicitely
put .arm directives into the exception code. Thumb-2 mode
has been tested on i.MX51 Babbage board.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add Mitac MioA701 board initial support.
The support provides basic boot and :
- a console over USB (serial gadget).
- the SD card support
- the MTD docg3 support
- the LCD support
Add a check in the default environment for a barebox.env
file on the first partition (FAT). If the file exists,
source it instead of the normal boot procedure.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We used to get the runtime offset of the board_init_lowlevel_return
by doing a &board_init_lowlevel_return. This does not work in thumb-2
mode, so use a separate linker section for this function instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Traditionally U-Boot and barebox have the exception vectors at
the start of the binary. There is no real reason in doing so,
because in the majority of cases this data will not be at 0x0
where it could be used as vectors directly anyway.
This patch puts the vectors into a separate linker section and
defines an head function which is placed at the start of the
image instead. Putting this in a separate function also has
the advantage that it can be placed at the start of images
which require an additional header like several Freescale i.MX
images. As the head function contains the barebox arm magic
those images can now also be detected as barebox images.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- this is taken from freescale-mx35-3-stack/3stack.c and allows
this board to run Freescale's kernel which relies on the system
revision to configure the correct PMIC.
- On rev0 boards (with DA9053), the log is :
detected i.MX53 rev 2.1
MCIMX53-START board 1.0
On newer boards (rev A or B with MC34708), the log is :
mc34708-i2c@mc34708-i2c0: MC34708 ID: 0x0014
detected i.MX53 rev 2.1
MCIMX53-START-R board 1.0 rev B
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
and register mc34708 which is present on MCIMX53-START-R board
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this allows I2C to work on boards which don't have external pull up
(like LOCO board)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixing this typo lets the barebox for pm9261 to be build.
Signed-off-by: Asen Chavdarov Dimov <dimov@ronetix.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add CCCR bits definition for PXA SoC, so that the bootloader
can setup a stable core clock frequency, which is not the
initial reset clock, as required by Intel's PXA27x Processor
family developer's guide, chapter 3.5.5, table 3.7 (clock
frequencies).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add standard GPIO routings for LCD panels, taken from linux
kernel.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As pxafb can rely on a PWM to control backlight, and because
driver dependencies are hard to deal with, remove automatic
enable of PXAFB on probe.
The user should in its environment do a :
- fb0.enable=1
This way, the PWM has been probed and is ready to work, and
the pxafb backlight control works.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add PXA embedded pulse width modulator support. The PWM can
generate signals from 49.6kHz to 1.625MHz.
The driver is for pxa2xx family. The pxa3xx was not handled yet.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current message indicating that SD card isn't
mounted is misleading if the card has only one
partition.
Updated the message to indicate that mounting
the specific partition failed.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some variants of the i.MX53 do not allow to run at 1GHz, so
pass a cpu frequency parameter to the lowlevel init function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Whether the controller works in 8bit mode is not only dependent
on the controller but also on the board having wired up 8 data
lines, so put a capabilities field in platform data.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove what is an apparently valueless Kconfig variable HAS_OMAP_NAND.
A search of the entire source tree shows:
$ grep -r HAS_OMAP_NAND *
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig:config HAS_OMAP_NAND
arch/arm/configs/phycard_a_l1_defconfig:CONFIG_HAS_OMAP_NAND=y
$
where the definition of that variable is simply:
config HAS_OMAP_NAND
bool
so it seems pretty clear it can be removed as nothing is using it.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Without the proper OMAP3 or OMAP4 dependency directives, you get the
wrong list of choices displayed based on which OMAP variant you pick.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
At least ARM allows us to dump the stack, but we currently
have no prototype for this. Add a dump_stack prototype and
provide a static inline function for architectures without
stack dump support. Also, call dump_stack() in panic() to
provide more information in the case of a panic.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
hang() only outputs 'reset the board' whereas panic
can be passed a string which we can use to output
some more information what is happening.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Otherwise the kernel would not register the nand partitions.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Extend DCD table and low level init routines. Add barebox SDRAM
device. Also, fix the memory size for bank 0 to 128MB. It was
accidently changed to 124MB here:
commit f928efa818
Author: Sascha Hauer <s.hauer@pengutronix.de>
Date: Tue Jul 19 09:58:32 2011 +0200
add a add_mem_device function
Add a helper function for boards to register their memory
devices. This makes the board code smaller and also helps
getting rid of map_base and struct memory_platform_data.
And switch all of the memory to it
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this allow to check we do not exceed the size of the SRAM as example
introduce BAREBOX_MAX_BARE_INIT_SIZE the maximum size of bare_init
this will allow your bare_init will fit in SRAM as example
ARCH can overwrite it via ARCH_BAREBOX_MAX_BARE_INIT_SIZE
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adding overlay support for phyCORE-i.MX35.
Also move the TEXT_BASE to leave enough space for the overlay image
at the end of the RAM.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adding overlay support for i.MX3 sdc.
Foreground channel only works when background is also enabled.
The foreground video mode is always the same as the background.
Also added alpha command to set the alpha value of the foreground.
Tested on a phyCORE-i.MX35.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added num_modes to all imx_ipu_fb_platform_data structs.
Removed defines for pcm043 to choose display.
We may switch this during runtime now.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Make support of multiple video modes possible for i.MX3 boards.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
board_init was moved to pure_initcall. broken since:
commit 0adce7ec68
Author: Sascha Hauer <s.hauer@pengutronix.de>
Date: Sun Jan 15 21:11:17 2012 +0100
ARM omap3: move board_init to pure_initcall
board_init initializes the mux and sdram. For both there is no
need to configure this so early. Move the code to a pure_initcall
and remove the surrounding unneeded code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
since commit 494a12f703
platform lowlevel init was moved to mach-omap.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
since commit ae2ac15105
a_init was renamed to omap3_core_init and called from board code.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
board_init is now called omap3_board_init. broken since:
commit 494a12f703
Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Date: Sat Jan 14 15:51:05 2012 +0100
omap3: move platform lowlevel init to mach-omap
this will allow to switch omap3 to standard organisation
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This function consists of only inline asm statements, so
use assembly in the first place. Also makes sure that the
function is compiled in arm mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
No need to do this so early. We can't print anything right
now anyway, so there is no need to setup vectors.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
There is no need to call a_init before relocation, so rename
the function to omap3_core_init and call it from board code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
board_init initializes the mux and sdram. For both there is no
need to configure this so early. Move the code to a pure_initcall
and remove the surrounding unneeded code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
Setting up the clocks does not work when the stack is in SDRAM.
Moving the stack to SRAM allows us to do the lowlevel clock setup
later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
The X-loader startup relocates to SRAM anyway, so there
is no need to be runnable from flash for the clock code.
This config is disabled in all defconfigs anyway, so remove
it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
this will allow to create it's own env/config
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to create it's own env/config
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to create it's own env/config
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to switch omap3 to standard organisation
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
in commit commit f60f6c58e
atmel_mci: check for device id we use to address the right slot
the driver use the dev_id to detect the slot which is wrong on 9263 as we have
2 devices with 2 slots
use slot_b paramter to specify the slot as done in linux
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to configure the nand as example
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When CONFIG_OMAP_BUILD_IFT is selected, the
target image name was set to "barebox.bin.ift".
This file must be renamed "MLO" before it can
be used on the SD card.
Make this as default behavior.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Enable the flag HAVE_NOSHELL to allow first stage
bootloader to be built for this board.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The base address passed for device "omap-hsmmc" was
incorrectly passed as OMAP_I2C1_BASE and the base
address for device "i2c-omap" was hardcoded to
0x4809C000 which, in fact, refers to OMAP_MMC1_BASE.
Similarly, in call to add_usb_ehci_device(), addition
is not required if right base address is used.
In fact, 0x48064700 (used as base in the addition)
falls in the OHCI Address space.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The config option CONFIG_GPMC is renamed to
CONFIG_OMAP_GPMC as result of this commit:
819f416b86
Still, sources continue to use CONFIG_GPMC.
Fix it.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
use ds3 for heartbeat and ds5 for dfu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
on 9269 and 9g20 the sram are mirrored at then of the bank so we can join them
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Without num_modes the imx fb driver won't work. Specify this
in the boards and also bail out in the driver when num_modes
is unspecified.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Using SSP1 since this is the default configuration.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this was introduced in "6b3e01a arm: eukrea: Fix compilation warning"
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
enable serial and dfu at the same time
senario if the usb device is plugged and the BP is not pressed at boot time
during 5s the usbserial will be enable
disable zlib support to fit in the 256K
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The lowlevel init function was a 1:1 copy from the babbage
baord, so it should be safe to switch to the generic C
lowlevel init.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Eric Benard <eric@eukrea.com>
Reimplement the code from lowlevel.S in C. It is run
from SDRAM anyway, so we can safely do this initialization
in a regular barebox environment instead in Assembly.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- move code which can be shared between i.MX53 and i.MX51
to a common file
- rename mx53_init_lowlevel to imx53_init_lowlevel
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
a) use the more CPU specific S3C* macro names
b) move the register description out of the way, as more recent CPUs using a
different layout and more features
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Keep common code in the MACH instead of re-inventing it in each platform.
Also use S3C* macros for all memory related register.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The UART is one of the units which differs only slightly inside the S3C family.
Prepare this driver to share it with more recent CPUs.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
After separation and after all S3C macros are now present, change the driver
to be more generic for future additions.
The timer registers in the S3C24XX family are only 16 bit wide. But these
registers can be read and written in a 32 bit manner. This is important to share
code with more recent CPUs which comes with 32 bit registers.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most members of the S3Cxxxx family share similar timer units. But they are
not really register compatible. To reflect this, use a separate name space for
the S3C family.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch just move the clocksource functions out of the generic.c source file
to handle it on a per CPU base later on.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are major differences in the clock tree of the S3C24xx family and the
more recent CPUs of the S3C family. Keep the S3C24XX clock routines separate to
avoid an ifdef hell. But also use generic function names to be able to
share drivers among the S3C family.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This LCD driver is for the LCD controller in the S3C2410/S3C2440 CPUs only.
Change its name to reflect its usage and free the way to add LCD controller
drivers for more recent Samsung CPUs.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The aready existing NAND controller driver in Barebox is for the S3C24XX family
only. Change the name of the file to reflect this fact (and free the way to add
more recent Samsung NAND controllers)
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Start with renaming files to share them in the S3C CPU family,
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The S3Cxxxx family consists of ARMv4, ARMv5 and ARMv6 types of CPU cores. The
S3C24xx sub family is only one of it. To be able to handle all CPUs in one mach
directory, use a more generic name for it.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds basic support for the mx28-evk board. Debug UART, MMC and FEC
have been successfully used.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Recent gcc generates code with unaligned access when architecture
supports it. Setting A bit unconditionally causes data-aborts on such
code rendering barebox unusable.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When executing 'bl' in inline assembler, the 'lr' register must be
marked as clobbered too.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
detect it at boot time
if the user button is pressed 5s and the vbus is 1 start the dfu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
drop irq id and rebase instead of of offset
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this device controller is present on rm9200/9260/9g20/9261/9g10/9263
the 9g45 use an other IP
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support the setup of the mmc voltage, when booting OMAP4 with twl6030
from nand.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added i2c support for omap4. Tested on pcm049.
Driver based on linux kernel implementation.
Also added a shift to access 16-bit registers
to make support for OMAP730/850 possible.
If accessing a non existing slave the bus will go into arbitration mode.
It's unable to recover from it.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a function to remap an IO range into a virtual addresses
range. This is particulary usefull for the few devices
mapped at physical address 0, as the MTD boot devices.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jean-Christophe PLAGNIOL-VILLARD
Alexander Shiyan
Sascha Hauer
Alexey Galakhov
Anand Gadiyar
Eric Bénard
Robert Jarzmik
Jan Luebbe
Antony Pavlov
Uwe Kleine-König
Krzysztof Halasa
Juergen Beisert
Jaccon Bastiaansen
Christian Kapeller
Wolfram Sang
Robert P. J. Day
Marc Kleine-Budde
Uwe Hermann
Esben Haabendal
Allan Heldgaard
Esben Haabendal
Asen Chavdarov Dimov
guenter.gebhardt@rafi.de
Teresa Gámez
Jan Weitzel
Michael Grzeschik
Sanjeev Premi
Roman Fietze
Juergen Kilb
Enrico Scholz
Alexander Aring
Daniel Mack