This adds a device_node member to struct cdev and a function
to find a cdev by device_node.
This also removes the setting of cdev->dev->device_node in
the of partition parser. We must not set the device since it
may not refer to a partition but to a whole device with partitions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of writing one word to the txfifo and then wait until
one is received in the rxfifo we can write until the txfifos
are not full and read as long the rxfifos contain data. This
makes transfers for the m25p80 driver around 7 times faster
here.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX SPI controller in version 2.3 can immediately start a transfer
when the txfifo is written to. In this mode we no longer have to trigger
the transfer with the xch bit which makes the code a bit simpler.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- make some locally used functions static
- remove read_passwd which is unused
- some refactoring to make code pathes clearer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We used to have the login functionality in the /env/bin/init script.
This is hard to review and it's too easy to break the login functionality
with changes to this script. Move the places to ask for a password to
C code where we have only a few places where we have to ask for a password.
Mainly these are run_shell() and the menutree command.
This patch introduces a login() function which will only return if the correct
password has been entered. Following calls will return immediately without
asking for a password again.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Different devices may report the reset source with different levels
of certainty. For example a SoC may see a power-on reset, but this
may only be because an external PMIC has power cycled the SoC. This
means the PMIC knows the real reason better and thus the reset reason
from the PMIC should be preferred.
This patch introduces priorities for the reset_source to handle the
above scenario. Also add a of_get_reset_source_priority() function
to retrieve the desired priority from the device tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a dev and name member to struct watchdog which helps distinguishing
between different watchdogs. Also add some debugging aids.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Put watchdogs on a list to allow multiple watchdogs. Add a priority
field to be able to pick the highest priority watchdog.
This patch also provides a of_get_watchdog_priority() function to
allow configuring the watchdog priority from the device tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This replaces the reset_cpu() function which every SoC or board must
provide with registered handlers. This makes it possible to have multiple
reset functions for boards which have multiple ways to reset the machine.
Also boards which have no way at all to reset the machine no longer
have to provide a dummy reset_cpu() function.
The problem this solves is that some machines have external PMICs or
similar to reset the system which have to be preferred over the
internal SoC reset, because the PMIC can reset not only the SoC but also
the external devices.
To pick the right way to reset a machine each handler has a priority. The
default priority is 100 and all currently existing restart handlers are
registered with this priority. of_get_restart_priority() allows to retrieve
the priority from the device tree which makes it possible for boards to
give certain restart handlers a higher priority in order to use this one
instead of the default one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some SPI NOR flashes support 4K erase blocks. 4K erase blocks do not
work with UBIFS which needs a minimum erase block size of 15360 bytes.
Also bigger sectors are faster to erase. This patch adds a device tree
option to use the bigger blocks instead of the default 4K blocks.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Not only the array containing the pointers should be const but
also the strings themselves, so instead of using const char **
use const char * const *.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So far we only supported blitting the whole screen from the shadow
fb to the framebuffer. Add a function to blit areas.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The fb core now has builtin support for offscreen rendering, use
this and drop offscreen handling in the gui code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For speeding up rendering we need shadow framebuffers. This is currently
implemented in the gui functions. This does not work properly when two
users (splash and fbconsole) use the same framebuffer since in this case
two different shadow framebuffers will be used. This patch implements
shadowfb handling in the fb core directly. With this the fb device gets
a parameter 'shadowfb'. When this is true the fb core will allocate a
shadow fb and provide it to the users.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is based on the code introduced to the kernel in
5f9296ba21b3c395e53dd84e7ff9578f97f24295.
Signed-off-by: Jan Luebbe <jluebbe@debian.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since we no longer have custom gpio function prototypes we can
drop the prototypes from asm-generic/gpio.h can add them to
include/gpio.h instead. While at it add static inline dummy wrappers
for !CONFIG_GENERIC_GPIO so that code using gpios can compile without
gpio support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add empty static inline function fallbacks if backlight support
is not enabled, so that drivers using the backlight don't fail to
build.
Fixes:
In function `simple_panel_ioctl':
undefined reference to `of_backlight_find'
undefined reference to `backlight_set_brightness_default'
undefined reference to `backlight_set_brightness'
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We have functions to setup the i.MX uart for early use, but these all
depend on DEBUG_LL. Move them to imx-uart.h to make them usable for
the regular PBL console.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With more stuff being done in PBL regular console support gets more and more
useful. This makes the PBL console independent of DEBUG_LL which is only
meant for early debugging but not regular output.
To use the regular PBL console a board must call pbl_set_putc() which stores
a pointer to the putc function to be used.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
LoaderTimeInitUSec and LoaderTimeExecUSec are used e.g. in systemd-analyze
to calculate the time spent in the firmare and barebox.
LoaderDevicePartUUID is used to mount the EFI partition to /boot.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch realizes framebuffer console support for barebox. It
supports colors and enough escape sequences to show the barebox
console and editor properly.
fbconsole mini-HOWTO
====================
1. compile sandbox barebox with
CONFIG_VIDEO=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_DRIVER_VIDEO_SDL=y
2. run barebox
3. test fbconsole
fbconsole0.active=oe
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Allocate the screen dynamically in fb_open. This opens the way to create
a fb_create_screen function which takes a struct fb_info * instead of a
filename. This is suitable for the framebuffer console which already has
a struct fb_info *.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The register defines will be used by the SPI xload code, so move
them to a place where the xload code can include them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
get_pixel converts a 32bit trgb color into framebuffer format. This
is useful for other code aswell, so export it.
Other functions in the graphics utils code use the name get/set_pixel
aswell, but instead of converting data they get a pixel from the framebuffer
or set a pixel on the framebuffer. To separate from these rename the
function to gu_hex_to_pixel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---=== SPD EEPROM Information ===---
EEPROM Checksum of bytes 0-62 OK (0xDF)
Total number of bytes in EEPROM 256
Fundamental Memory type DDR2 SDRAM
SPD Revision 1.2
---=== Memory Characteristics ===---
Maximum module speed 800 MHz (PC2-6400)
Size 2048 MB
Banks x Rows x Columns x Bits 8 x 14 x 10 x 64
Ranks 2
SDRAM Device Width 8 bits
Module Height 30.0 mm
Module Type SO-DIMM (67.6 mm)
DRAM Package Planar
Voltage Interface Level SSTL 1.8V
Module Configuration Type No Parity
Refresh Rate Reduced (7.8 us) - Self Refresh
Supported Burst Lengths 4, 8
Supported CAS Latencies (tCL) 6T
tCL-tRCD-tRP-tRAS 6-6-6-18 as DDR2-800
Minimum Cycle Time 2.5 ns at CAS 6
Maximum Access Time 0.40 ns at CAS 6
Maximum Cycle Time (tCK max) 8 ns
---=== Timing Parameters ===---
Address/Command Setup Time Before Clock (tIS) 0.17 ns
Address/Command Hold Time After Clock (tIH) 0.25 ns
Data Input Setup Time Before Strobe (tDS) 0.05 ns
Data Input Hold Time After Strobe (tDH) 0.12 ns
Minimum Row Precharge Delay (tRP) 15.00 ns
Minimum Row Active to Row Active Delay (tRRD) 7.50 ns
Minimum RAS# to CAS# Delay (tRCD) 15.00 ns
Minimum RAS# Pulse Width (tRAS) 45.00 ns
Write Recovery Time (tWR) 15.00 ns
Minimum Write to Read CMD Delay (tWTR) 7.50 ns
Minimum Read to Pre-charge CMD Delay (tRTP) 7.50 ns
Minimum Active to Auto-refresh Delay (tRC) 60.00 ns
Minimum Recovery Delay (tRFC) 127 ns
Maximum DQS to DQ Skew (tDQSQ) 0.20 ns
Maximum Read Data Hold Skew (tQHS) 0.30 ns
---=== Manufacturing Information ===---
Manufacturer JEDEC ID 7f 98 00 00 00 00 00 00
Manufacturing Location Code 0x05
Part Number
Manufacturing Date 2014-W47
Assembly Serial Number 0x43266892
Signed-off-by: Alexander Smirnov <alllecs@yandex.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Complex video pipelines are modelled with the of_graph bindings in
the devicetree. This patch adds a ioctl infrastructure to issue
commands to the remote endpoint of a of_graph. Currently defined
ioctls are prepare/unprepare, enable/disable and get_modes. This
is enough to control LVDS or HDMI encoder or simple panels.
A device node which contains of_graph endpoints can be registered
as a VPL entity. An entity can receive ioctls via the .ioctl callback
and also issue ioctls by calling vpl_ioctl. The core itself will never
iterate over the entire pipeline. Instead, the different VPL entities
should forward an ioctl to the next instance in the pipeline whenever
necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
exitcall infrastructure is based on initcall infrastructure.
It allows to have and use exit call hooks on barebox shutdown.
Signed-off-by: Herve Codina <Herve.CODINA@celad.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When a framebuffer is kept enabled when Linux starts its framebuffer
memory should be reserved. Otherwise Linux may overwrite its contents.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The most standard update handler will simply copy a file to a device.
This can be shared across several users, so add a standard handler for
this operation.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
register_preset_mac_address only works when CONFIG_PARAMETER
is enabled because otherwise dev_set_param is a no-op. Add a
function to set the MAC address explicitly without the need
of CONFIG_PARAMETER and use it where appropriate.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The mtd concat layer supports concatenating several MTD devices
into a single one. This is nearly as-is from the corresponding
Kernel code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This function is needed for the fixed length string feature in the state
framework.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add the parameter to boot from ubifs fileystems. This assumes that
there will be only one UBI device registered in the kernel, otherwise
there is no way to predict the ubi number.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When registering a filesystem device add a device parameter suitable
for the Linux root= option to boot from exactly this filesystem. Currently
the fs layer sets this parameter to the root=PARTUUID= mechanism if a
partuuid is available. Other filesystems like NFS and UBIFS which do
not have a PARTUUID can overwrite this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds the partuuid string to struct cdev in order to have this
available for constructing a suitable Linux root=PARTUUID= option
for booting Linux.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a globalvar string function to pass a pointer to a string.
With this we can directly access the string to get the variable and
don't have to getenv() the string first.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Matching a device node is enough since a device node may have
multiple PWMs. Check for a id aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a small backlight layer. It provides a backlight device
on which the brightness parameter can be used to adjust the brightness.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The code can be used with slight modifications on i.MX28 aswell.
Add a i.MX28 registration function and move the differences to
function callbacks.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We used to collect all sections beginning with __clk_of_table_ in a single
section in the linker using KEEP(*(.__clk_of_table_*)). That the sentinel
entry ended up as the last entry was pure luck, but not always the case.
Instead of putting all entries in different sections we now put all entries
in the same section. Only the sentinel entry gets its own section and is
collected by the linker separately.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Andreas Willig <andreas.willig@rafi.de>
Tested-by: Andreas Willig <andreas.willig@rafi.de>
Currently code needs to fiddle with the active parameter of a console
device directly to enable/disable consoles. Add console_set_active()
to set the status and console_get_active() to get the current status.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
dhcp/bootp was bound to the command functionality.
This patch splits the dhcp command.
We are now able to use bootp without a shell.
This patch adds also a check for environment variables and globalvar.
So only when ENVIRONMENT_VARIABLES and GLOBALVAR is set, all received
dhcp data will be stored.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The nlink_t type is unused in barebox, so drop it. This prevents
compile failures when architectures use the generic posix_types.h
which no longer has __kernel_nlink_t defined.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most types defined in posix_types.h are architecture independent,
so instead of repeating this for each architecture add a generic
file that can be used by architecture code. To use it an architecture
must define BITS_PER_LONG properly in asm/bitsperlong.h.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes the following warning:
CC arch/arm/boards/foo/board.o
In file included from arch/arm/boards/foo/board.c:22:0:
include/habv4.h:24:19: warning: function declaration isn't a prototype [-Wstrict-prototypes]
static inline int habv4_get_status()
^
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The kernel has __BITS_PER_LONG and BITS_PER_LONG. The formaer
is needed for architectures which support 32bit userspace on a
64bit kernel. This is not relevant for barebox, so drop
__BITS_PER_LONG and use BITS_PER_LONG only.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of letting all architectures define their own dma_addr_t use
a common place in include/linux/types.h and use a Kconfig symbol that
architectures can select to define the width of dma_addr_t. The same
is done in the Kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit 2e6a88f210 (add cpu native ordered io accessors) introduced
these macros and then commit be57f20cdd (Fix big endian MMIO
primitives) figured out they are equivalent to __raw_{read,write}*.
They turned out unnecessary after all. Anyway, most source files
use __raw_read* and __raw_write*.
Let's replace a few remaining references and abolish them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This function is needed when a device that already registered a fixup in
the probe routine fails later to probe completely. Without unregistering
the fixup the function might later be called with invalid data.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch improves the backend property, it can be either a phandle or a
of_path. During probe() of the state driver the backend property is
dereferenced and the resulting of_path is saved in the state context. In a
later patch it will be used to generate a phandle reference to the backend
during DT fixup.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To allow init code that depends on the environment being loaded.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add two functions to calculate values for UBMR and UBIR
registers. This way both early serial initalization code and
serial_imx.c can use them and not duplicate the code.
Singed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move UART definitions into a separate file to avoid redefinition in
<mach/debug_ll.h> and magical constants in low level UART
initialization code.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
USB requests should be processed within a timeframe of 5s.
The linux kernel also uses this timeout value for the control packets.
For the musb the increase in timeout helps successfully probing USB devices
(at least on one test hardware), but on the other hand doesn't slow down the
system, if there are no devices, i.e. the timeout never hits. That means,
that the USB core correctly aborts instead of timing out.
Why and how the 100ms was chosen in the first place, can not be deduced from
the git history, just that it seems to work fine for most boards.
Change USB_CNTL_TIMEOUT to 5000ms and replace all occurences of
`USB_CNTL_TIMEOUT * x`
with just
`USB_CNTL_TIMEOUT`,
as the timeout is now large enough without it.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since 2011 barebox' of_device_id struct uses unsigned long type for data field:
struct of_device_id {
char *compatible;
unsigned long data;
};
Almost always struct of_device_id.data field are used as pointer
and need 'unsigned long' casting.
E.g. see 'git grep -A 4 of_device_id drivers/' output:
drivers/ata/sata-imx.c:static __maybe_unused struct of_device_id imx_sata_dt_ids[] = {
drivers/ata/sata-imx.c- {
drivers/ata/sata-imx.c- .compatible = "fsl,imx6q-ahci",
drivers/ata/sata-imx.c- .data = (unsigned long)&data_imx6,
drivers/ata/sata-imx.c- }, {
Here is of_device_id struct in linux kernel v4.0:
struct of_device_id {
char name[32];
char type[32];
char compatible[128];
const void *data;
};
Changing of_device_id.data type to 'const void *data' will increase
barebox' linux kernel compatibility and decrease number of 'unsigned
long' casts.
Part of the patch was done using the 'coccinelle' tool with the
following semantic patch:
@rule1@
identifier dev;
identifier type;
identifier func;
@@
func(...) {
<...
- dev_get_drvdata(dev, (unsigned long *)&type)
+ dev_get_drvdata(dev, (const void **)&type)
...>
}
@rule2@
identifier dev;
identifier type;
identifier func;
identifier data;
@@
func(...) {
<...
- dev_get_drvdata(dev, (unsigned long *)&type->data)
+ dev_get_drvdata(dev, (const void **)&type->data)
...>
}
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
amba_{g,s}et_drvdata macros from linux kernel use
dev_{g,s}et_drvdata functions.
But in linux dev_get_drvdata() takes only one argument
while in barebox dev_get_drvdata() takes two arguments.
There is no dev_set_drvdata() in barebox at all.
So amba_{g,s}et_drvdata macros from linux are
unusable for barebox.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Registering mbus driver as platform driver is a little late for
some register accesses to work. We have to make sure boot-up
mbus windows are disabled early, so call mbus driver directly
from SoC init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a driver for SPI master by GPIO pins.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds a flags argument to the of_find_path() function. The only flag
defined for now is OF_FIND_PATH_FLAGS_BB. When used on NAND devices, the
function returns the bad block aware device (the ".bb" device).
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch factors out the wait-for-key-press loop from the shell command
"timeout" into a sparate file, so that it can be used from C, too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Otherwise compilation may fail with:
include/fdt.h:11:15: error: unknown type name 'uint64_t'
static inline uint64_t fdt64_to_cpu(uint64_t x)
include/of.h:22:19: error: field 'list' has incomplete type
struct list_head list;
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There should be no reason to ever change the data pointed to by id_table
or of_compatible. So make this offical by adding some 'const's.
In Linux the corresponding pointers are marked as const, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
dev->priv is for private use of the device driver, so do not
use it in the pci core. Instead, introduce a id field in struct
pci_device.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
As expected, we would need deferred probing sooner or later. This is
a first approach to allow devices to return -EPROBE_DEFER and get
sorted into a list of deferred devices that will be re-probed later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As hinted in the linux kernel driver, pxa platforms such as mainstone,
stargate and idp have a broken design, where half-word writes not
aligned to a word address are not working.
This patch is a taking back the half-word write accessor for this
specific case from the linux kernel.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit b8a1bb1dd2 (pci: defer device registration until after bridge setup)
changed the activation order of devices, so that bridges above the devices could
be configured properly before activating the devices below. This commit failed
to acknowledge that there may be devices located directly on the root bus without
any bridge in between and so those devices would never get enabled.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
current implementation
$ ls -al build/versatilpb/arch/arm/pbl/zbarebox.bin
-rw-r--r-- 1 root root 211095 Mar 24 13:21 build/versatilpb/arch/arm/pbl/zbarebox.bin
linux generic implementation
$ ls -al build/versatilpb/arch/arm/pbl/zbarebox.bin
-rw-r--r-- 1 root root 210829 Mar 24 13:21 build/versatilpb/arch/arm/pbl/zbarebox.bin
on a compressed lzo barebox we will 266 bytes
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As we will use the best sha algo at runtime
Add a new init level crypto_initcall to ensure that all the sha present
before hmac
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to have hw driver or asm optimised driver.
Use a priority level to determine which one to use at runtime.
The generic one will be 0.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
such as RSA as we load a DER key we will detect the key size
at runtime and so the algo length.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
such as for hmac(xxx) you must provide a key
This will allow to enforce the correct parameter at digest command
<digest>sum is not impacted
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
That can be used for digest calculation and verify
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Taken from the Kernel, put into the same place as in the kernel,
although the hexdump.c does not actually contain hexdum functions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow as example to list the currently supported digest.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to generate a KEY + IV based on a password and salt for AES
encryption/decryption as example
or simply the key for hmac or rsa from text password
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Combination of @init and @update and @final. This function
effectively behaves as the entire chain of operations, @init,
@update and @final issued in sequence. This is added for hardware
which cannot do even the @finup, but can only do the whole
transformation in one run.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to compare a md with the original one
When calling this do not call final
For RSA_SIGN verification final does not exist only verify
as final will be for signing
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
expect the key to be set before calling
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sync the pci register definitions with Linux 4.0-rc1. Some are needed
for the upcoming designware pcie driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
pass the key via -h param
barebox@barebox sandbox:/ sha256sum -h test /dev/fd0
c297473e9bb221c5dc51d47ad75c76095f1bdc4ca9dff1d5931c2e22bf11a0de /dev/fd0 0x00000000 ... 0xffffffffffffffff
use the same idea as openssl command
$ openssl dgst -sha256 -hmac "test" TODO
HMAC-SHA256(TODO)= c297473e9bb221c5dc51d47ad75c76095f1bdc4ca9dff1d5931c2e22bf11a0de
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the hmac algo will be registered as hmac(%s) such as hmac(sha256)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Taken from the Kernel, put into the same place as in the kernel,
although the hexdump.c does not actually contain hexdum functions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds a framework to describe, access, store and restore a set of
variables. A state variable set can be fully described in a devicetree node.
This node could be part of the regular devicetree blob or it could be an extra
devicetree solely for the state. The state variable set contains variables of
different types and a place to store the variable set.
For more information see:
Documentation/devicetree/bindings/barebox/barebox,state.rst
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now you need to call digest_alloc and when you finish to use it digest_free.
We need this for upcomming aes encryption support and secure boot
as we will need multiple instance of the same digest.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to move from a one at a time digest to a multi-instance
with too much impact on the code using it
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit 03b59bdb64 (paramter: The dev_add_param_*() return ERR_PTR(),
change no-ops to return ERR_PTR(-ENOSYS) instead of NULL) started using
ERR_PTR and errnos without including the relevant header.
This fixes the build for a lot of configurations.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This better separates the DMA from the MMU functionality.
Also move all drivers that only depends on asm/mmu.h for the alloc
functions over to the common header.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow us to implement cache maintenance in a platform
agnostic way.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It is needed for container_of() and this header falls
over if we change the include order.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It is required for Rockchip SoCs where clock settings registers have
write-enable mask in high word.
Signed-off-by: Andrey Panov <rockford@yandex.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It is required for Rockchip SoCs where clock settings registers have
write-enable mask in high word.
Signed-off-by: Andrey Panov <rockford@yandex.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some SoCs have special device pins for external reset signals.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sometimes it's useful to test if a memory operation works or
aborts. This adds data_abort_mask() to ignore data aborts and
data_abort_unmask() to enable them again. This is used in the
next step for the 'md' command so that illegal addresses just
show 'xxxxxxxx' instead of crashing the system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a function to parse a full cmdline partition string. The
addpart command is switched to use this function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The return size should be loff_t to support partitions bigger
than 4G. Also use const for the devname and endp.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the bb devices which are created in add_mtd_device() must be removed
in del_mtd_device(). Also remove deletion of the bb devices in the
mtdparts-add environment file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will use the device name as regulator name
with the same Algo as clkdev for lookup
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
All the smcs family chips 91c94, 91c96, 91c100, 91c111 share almost the
same behavior and register sets. The noticeable exceptions are coped
with in this patch, ie :
- 91c94 and 91c96 only have an internal 10 Mbps phy
The registers used for phy discovery on later chips will corrupt the
91c96 state.
- 91c94 and 91c96 have a control and config register quite different
from their 91c1xx conterparts
A platform data user defined couple of registers is introduced. If
these values are 0, 91c1xx legacy behavior is assumed.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Smc network IPs can be wired up in different funny ways. For example the
lubbock pxa25x development platform wires all address lines shifted by
2, ie. bus A2 is smc91c96 A0, bus A3 is smc91c96 A1 etc ...
In order to cope with the different possible combination, add a shift
parameter for addresses.
By default, the old behaviour using the 32 bit accesses is kept.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This function is only used in drivers/usb/*.
It is equivalent to mdelay().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The include/common.h is still cluttered (although much better than
U-Boot). It contains various utility macros that originates
in Linux. Move them to the original place, include/linux/kernel.h,
to slim down include/common.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In Linux, these macros are defined in include/asm-generic/bug.h.
To tidy up common.h, move BUG(), BUG_ON(), WARN(), WARN_ON() there.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In Linux, the macros BUILD_BUG_ON* are defined in include/linux/bug.h.
To tidy up common.h, move BUILD_BUG_* there.
MAYBE_BUILD_BUG_ON is not used in barebox and it was removed from Linux
long time ago. Drop it from barebox, too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The parameters ECC Strength, BadBlockMarkerByte and BadBlockMarkerStartBit in
the FCB structure depends on the nand chip's pagesize and oobsize. Instead of
hardcoding these values into the imx6 bbu handler calculate these values on the
fly. Therefore we export the necessary functions from the nand_mxs driver to
use them in the bbu handler.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Linux uses SHRT_* instead of SHORT_*. The <limits.h> of C does
the same. Let's follow this standard.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Linux defines *_MAX, *_MIN macros in include/linux/kernel.h.
Let's follow this way to slim down the common.h.
This change should have no impact because include/common.h already
includes <linux/kernel.h>.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most of the implementations of PUTC_LL() takes "char"
(some take "int"), not "unsigned char".
Moreover, puts_ll() takes an argument with "const char *" type.
Let's drop "unsigned" from the prototype of putc_ll().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The driver is taken from the Linux kernel, with the following changes :
- all DMA removed
- all asynchronous handling removed, including the interrupt handler,
and the asynchronous state handling
- pxa armada support removed
Most the kernel structure was kept, to ease up future fixes integration
from the kernel driver.
The driver is tested on a pxa3xx system development
board (aka. zylonite), and reading, writing, erasing, and bad block
management were tested.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can use dynamic number id with specific devname
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Looks like I am also highly addicted to Linux...
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This file originates in Linux. Linux has it under include/linux/
directory since commit dccd2304cc90.
Let's move it to the same place as well in barebox.
This commit was generated by the following commands:
find -name '*.[chS]' | xargs sed -i -e 's:<sizes.h>:<linux/sizes.h>:'
git mv include/sizes.h include/linux/
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
broken since
commit ed6e965824
Author: Sascha Hauer <s.hauer@pengutronix.de>
resource: Let dev_request_mem_region return an error pointer
Introduce dev_request_mem_region_err_null
only used on platform like at91 where the resource address conflicts
with errno PTR.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds simple console support to the PBL which makes it
possible to print more complex messages in the PBL than just
strings or hex numbers. For now puts_ll is used to print the
messages, so it depends on CONFIG_DEBUG_LL which makes it
more a debugging option. However, this could be extended later
to get regular output from the PBL if desired.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The netconsole needs to be able to deny activation when the network
has not been enabled. Add an optional callback to the console for
this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Implement the standard FS ops for writing/manipulating
efivars.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A proper GUID is needed to namespace all sorts of
things, most prominently persistent variables.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows to actually reset the system from barebox
instead of dropping back into the EFI firmware.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Thanks to the wonders of UEFI we have to walk down the
device path all the way until we arrive at the device
we got this path from...
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
No architectue implements its own gpio_is_valid() function, so move
the only existing implementation to include/gpio.h where it's available
for all users.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This commit adds support for Marvell's 88E1543 PHY chip. This chip is
almost identical to the 88EE1545, except the 88E1545 supports QSGMII
and the 88EE1543 supports SGMII.
Therefore, the same configuration function is used for both PHYs. For now,
the only initialization provided for the 88EE1543 is the LED setup.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This commit adds support for Marvell's 88E1545 PHY chip. In particular, this
allows to support QSGMII interfaces.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This could previously only be done with 'devinfo global'. While
this is still possible this adds a more direct access via the
globalvar command. This variant also adds a '*' in front of
the variable if the corresponding non volatile variable exists.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds (back) support for non volatile variables. Non volatile
variables are variables which are stored in the environment over
reboot. They are used in the same way as the global variables, but
with a 'nv' command and device. The variables are stored under
/env/nv/, one variable per file. Adding a nv variable automatically
adds a global variable with the same name. Changing a nv variable
also changes the same global variable, but not the other way round.
This allows for example to configure the username as:
nv user=sha; saveenv
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sometimes mbr is erroneously recocognised as FAT partion. Due to this the mbr
partition parser is not being called and the partitions on the media are not
detected. This patch should fix the problem. The checking is done as in the
linux kernel.
I have seen the problem using usb sticks. Although partitioning and formatting
them under linux. The file system type field in the mbr remains there which
causes the wrong detections as FAT32 type and not as mbr.
Signed-off-by: Zahari Doychev <zahari.doychev@linux.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds xz decompression support from the kernel. Both compressing
the barebox binary with xz and decompressing xz files on the commandline
is supported.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some SoCs are able to detect if they got reset
in response to an overtemperature event.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This brings in the generix PHY framework from Linux.
I tried to strip it down as much as possible while
keeping it useful.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Function to enable and register a disabled device.
The devices can be registered using the
device node with of_device_enable_and_register() or
with the device node name/path by using the
of_device_enable_and_register_by_name() function.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
dev_add_param creates a new parameter so it makes more sense to
return it than to return an error code. Since the return value
is hardly ever checked this is only a small patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The struct device_d * in struct filep is never of interest, instead
it is always converted to a struct fs_device_d *, so simplify the code
by storing the struct fs_device_d * directly.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So that PCI devices hang down from bridges and root
bridges down from the PCI host controller when
calling devinfo.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some host controllers provide a prefetchable
memory area and devices will prefer this for
some of their BARs.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Without console support we need a static inline version of
pr_print and dev_printf, otherwise we get link errors.
Reported-by: Kevin Du Huanpeng <u74147@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Set a property to a phandle of a child node. This may be used
for selections like display-timings.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added of_parse_phandle_from() to be able to use external root nodes.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added of_find_node_by_phandle_from() to find nodes by
phandle with a given root node.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added for_each_node_by_name_from() to be able to
pass external root node.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a buffer for log messages and a 'dmesg' command to
print the messages. The log buffer is implemented as log objects
rather than a string buffer. This makes it easy to implement
limiting the messages, cleaning the buffer and timestamping
the messages.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For measuring the startup time it's useful to save the first
timestamp after the clocksource has been registered.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This changes the MUSB support from the original Kernel state to
be usable with barebox. Tested on a custom board and the Beaglebone
Black. The host port on the Beaglebone works, the OTG port works
in device mode, but not yet in host mode.
Based on the initial MUSB port from Rolf Evers Fischer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds the necessary files from the MUSB driver directly from Linux
3.17-rc5. No changes to the original files have been made so far.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of letting each driver implement usb_gadget_poll directly
implement this function in the core which then calls into the
drivers.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Multi-SoC support for MVEBU will add mbus ranges for all compiled
SoCs. To protect the mbus node of the SoC barebox is executed on
from others ranges, pass machine's compatible to mvebu_mbus_add_range
and check before applying the fixup.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
phy_wait_aneg_done() is directly called by the network code, so it
should not read phy registers directly. Introduce phy_aneg_done to
give phy drivers the chance to do something different to poll for
autonegotiation completion.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So they can be used in board files to register
fixups.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This framework handles a list of registered Firmware programming handlers
to unify a firmware programming interface by hiding the details how
to program a specific Firmware in its handler. This is created with FPGAs
in mind but should be usable for other devices aswell.
A user has two possibilities to load a firmware. A device file is create
under /dev/ which can be used to copy a firmware to. Additionally a
firmwareload command is introduced which can list the registered firmware
handlers and also to upload a firmware.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It's often useful to get some information about a barebox image
before starting or flashing it. This patch introduces barebox
Image MetaData (IMD). When enabled a barebox image will contain
a list of tags containing the desired information. We have tags
for:
- the barebox release (2014.07.0-00160-g035de50-dirty)
- the build timestamp (#741 Mon Jul 28 15:08:54 CEST 2014)
- the board model the image is intended for
- the device tree toplevel compatible property
Also there is an additional generic key-value store which stores
parameters for which no dedicated tag exists. In this patch it
is used for the memory size an image supports.
Since there is no fixed offset in a barebox image which can be
used for storing the information, the metadata is stored somewhere
in the image and found by iterating over the image. This works
for most image types, but obviously not for SoC images which are
encoded or encrypted in some way.
There is a 'imd' tool compiled from the same sources for barebox,
for the compile host and for the target, so the metadata information
is available whereever needed.
For device tree boards the model and of_compatible tags are automatically
generated.
Example output of the imd tool for a Phytec phyFLEX image:
build: #889 Wed Jul 30 16:08:54 CEST 2014
release: 2014.07.0-00167-g6b2070d-dirty
parameter: memsize=1024
of_compatible: phytec,imx6x-pbab01 phytec,imx6dl-pfla02 fsl,imx6dl
model: Phytec phyFLEX-i.MX6 Duallite Carrier-Board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
read_file has some limitations:
- It is not possible to check the error code since read_file returns
NULL for failure
- It is not possible to limit the buffer size to sensible limits.
This patch introduces read_file_2 which doesn't have these limitations.
read_file becomes a wrapper around read_file_2.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We have our file helper functions in several places. Move them
all to lib/libfile.c.
With this we no longer have file helpers in fs/fs.c which contains
the core fs functions and no functions in lib/libbb.c which are
not from busybox.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In order to be able to mark an stored envfs image with special features
(intentional ignore for example), we now can feed forward these flags.
By forwarding a '0' for the flags nothing changes because the envfs superblock
was already allocated with xzalloc.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a simple flag to envfs to be able to mark an external environment as
"not to be used".
This change should not affect existing systems, because the current envfs
implementation ensures the 'flags' member in the envfs master block is always
zeroed.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on Linux's support by Thomas Petazzoni:
commit b9d12085f2f531fdea67f0361564e0812696227c
Author: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Date: Tue Apr 15 15:50:19 2014 +0200
net: phy: add minimal support for QSGMII PHY
This commit adds the necessary definitions for the PHY layer to
recognize "qsgmii" as a valid PHY interface. A QSMII interface, as
defined at
http://en.wikipedia.org/wiki/Media_Independent_Interface#Quad_Serial_Gigabit_Media_Independent_Interface,
is "is a method of combining four SGMII lines into a 5Gbit/s
interface. QSGMII, like SGMII, uses LVDS signalling for the TX and RX
data and a single LVDS clock signal. QSGMII uses significantly fewer
signal lines than four SGMII busses."
This type of MAC <-> PHY connection might require special handling on
the MAC driver side, so it should be possible to express this type of
MAC <-> PHY connection, for example in the Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When using more than one PCI bus, we have to assign unique numbers
to each bus. Use an auto-incremented bus index and assign it to
each registered bus. Also, allow the PCI host controller to update
internal registers by calling set_busno with assigned bus number.
While at it, add pci_controller struct to set_busno callback,
add a back reference to pci_controller to pci_bus, and clean up
unused left-overs from Linux import.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for xHCI USB 3.0 host controllers found on various
SoCs and PCI devices. Currently, the driver only supports the virtual
USB 2.0 ports of the host controller, so if you plan to use USB 3.0
devices, put a USB 2.0 cable in between.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This imports {lower,upper}_32_bits defines to allow to get upper
and lower 32b part of a 64b number.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
EHCI HCD has a private version of min3() determining the smallest
number out of 3. We already have min()/max() imported from Linux,
also get min3()/max3() and use it instead of EHCI's private one.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On Marvell MVEBU SoCs internal registers are usually remapped from reset
default. While Dove and Kirkwood always had their registers remapped,
some Armada 370 and XP where shipped with bootloaders that did not remap
them.
On Barebox these registers are remapped early and on all MVEBU SoCs, so
provided DTs should always reflect that in their mbus ranges property.
This patch registers a fixup for DTBs and allows individual SoCs to add
specific remap ranges to the fixup list. The fixup is registered on
pure_initcall to even allow to fixup pbl or appended DTBs.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We imported a bunch of defines with ch9.h and ch11.h that are now
duplicated in usb_defs.h. Get rid of each duplicate in usb_defs.h
and prefer the ones from ch9.h and ch11.h.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use the descriptors from ch11.h instead of duplicating them
in usb.h. usb_hub_descriptor now contains a union .u to differentiate
HS hub descriptor from SS hub descriptor.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
{Device,Interface,Endpoint}Requests are currently defined in private
ehci.h but are also useful for other drivers than ehci-hcd. Move them
to usb/usb_defs.h and also add some more class requests.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
All other descriptors have their length field named bLength, except
imported usb_hub_descriptor from Linux uses bDescLength. Adjust the
name to match the others.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Barebox supports up to 8 USB devices attached on a Hub, Linux does 31.
Reduce the USB_MAXCHILDREN define in ch11.h to the Barebox one and
put a comment above.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Linux has an extra include for chapter 11 (Hub Specification) of USB 2.0
spec. We already have a ch9.h, so import the one from Linux.
Barebox specific changes will be patched up later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Similar to the Kernel multi function this gadget driver is used
for creating a USB device with multiple functions. This is
created and removed with the newly created 'usbgadget' command.
Based on the options it creates combinations of DFU, fastboot
and serial USB functions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Android fastboot protocol Can be used to update firmware and to
issue other lowlevel commands to the bootloader. This adds a
fastboot implementation based on the U-Boot fatboot code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently we only have version_string which contains information
about the date the binary was compiled and by whom it has been
compiled. This adds a release_string which only contains the
plain release version.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Register DFU as usb_function_instance to make it work with composite
gadgets. Also use this internally for registering as DFU device (with
the 'dfu' command).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The dfu command parses a string which contains a list of
devices and flags. This format is useful for other users
aswell, so add common helper functions to parse it and
let the dfu command use this format.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This introduces the device parameters:
usbgadget.product
usbgadget.vendor
usbgadget.manufacturer
usbgadget.productname
These variables are used to configure the USB vendor id, product id,
manufacturer name and product name.
Previously these were configured with arguments to the usbserial
and dfu command. The parameters are device static, so it's nice to
configure it somewhere in the environment instead of when calling
dfu/usbserial. Also when other gadget drivers are added we do not
have to duplicate the option parsing further.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This function allows drivers to create a string parameter and
provides access to it via a pointer. Using regular dev_add_param
only allows access via dev_get_param().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We can now detect changes in the USB device hierarchy properly, so
the 'force' option to the usb command is no longer necessary. We just
scan the busses each time the usb command is called.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds U-Boot 'usb tree' command functionality to barebox.
Here is an example output:
1 ID 0000:0000
| u-boot EHCI Host Controller
|
+-2 ID 05e3:0606
| USB2.0 Hub
|
+-3 ID 10c4:ea60
| Silicon Labs CP2102 USB to UART Bridge Contr P-00-00669
|
+-4 ID 05e3:0606
| | USB2.0 Hub
| |
| +-5 ID 05e3:0608
| | | USB2.0 Hub
| | |
| | +-6 ID 0d8c:000c
| | C-Media USB Headphone Set
| |
| +-7 ID 0d8c:000c
| C-Media USB Headphone Set
|
+-8 ID 0846:1040
NETGEAR NETGEAR FA120 Adapter
The tree view is enabled with 'usb -t'
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For situations when we don't know the desired mode for the OTG port
we register a otg device which has a mode parameter to specifiy the
desired mode on the command line.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We have USB_SPEED_* definitions as macros in usb_defs.h and as an enum
in ch9.h. The defines in usb.h correspond to hardware bits in the
ehci controller. Get rid of them and keep the hardware independent
enums.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently we have two conflicting definitions of struct usb_config_descriptor
and struct usb_interface_descriptor in the tree. This is because the USB code
uses additional fields in the structs for internal housekeeping. Add
struct usb_interface and struct struct usb_configuration with the housekeeping
data and embed the corresponding hardware structs into them. This frees the
way to use the definitions from ch9.h in the next step.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Yes, we already have roundup/rounddown. Unlike these macros
round_up/round_down are optimized to (and only work with)
power-of-2 arguments. It's a poor name, but kernel code needs
it, so add it to barebox aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
During debugging it sometimes helps to me even more verbose. This
adds an additional debug level for this. Also we remove an already
existing pr_vdebug definition in the USB gadget u_serial driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
use in devinfo Protocols
Tested today on qemu with all the GUID translated
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch imports i2c_smbus_{read,write}* functions from linux-3.15.
Here is a quote from linux.git/Documentation/i2c/smbus-protocol:
If you write a driver for some I2C device, please try to use the SMBus
commands if at all possible (if the device uses only that subset of the
I2C protocol). This makes it possible to use the device driver on both
SMBus adapters and I2C adapters (the SMBus command set is automatically
translated to I2C on I2C adapters, but plain I2C commands can not be
handled at all on most pure SMBus adapters).
So having i2c_smbus_{read,write}* functions in barebox makes
porting of linux i2c client drivers much easier as many drivers rely on
these smbus functions.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With upcoming EFI payload support the efi.h file will diverge
from the kernel, so move it from include/linux/ to include/
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
EFI uses 16 bit character strings. Add beginning support for this.
Since barebox uses 8 bit strings internally we need conversion functions
to convert between 16 bit and 8 bit strings.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a devname field to struct console_device so that the device
name can be set by the driver. This makes it possible to have
persistent device names.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some devices may have a much more efficient way to output strings
rather than single characters. Let console devices implement a
callback for this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
unsigned long is 64bit wide on some architectures. Make IPaddr_t a
typedef to uint32_t to make sure it's 32bit wide.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
remove unused function declarations and definitions:
- vallocc is #if 0 in source code
- pvalloc is defined but not used
- cfree is defined but not used
- malloc_usable_size is unused
- mallopt is not defined
- mallinfo is not defined
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This driver is based on Linux 2.6.39 8139too driver.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The doxygen documentation is long outdated. Remove it. It will
be replaced with sphinx based documentation later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>